124 topics in this forum

    • 4 replies
    • 245 views
    • 2 replies
    • 220 views
    • 5 replies
    • 295 views
    • 13 replies
    • 651 views
    • 7 replies
    • 273 views
    • 2 replies
    • 724 views
    • 4 replies
    • 245 views
    • 4 replies
    • 303 views
    • 30 replies
    • 4,185 views
    • 1 reply
    • 380 views
    • 13 replies
    • 1,610 views
    • 2 replies
    • 298 views
    • 2 replies
    • 482 views
    • 2 replies
    • 312 views
    • 1 reply
    • 1,408 views
    • 11 replies
    • 1,115 views
    • 4 replies
    • 575 views
    • 8 replies
    • 496 views
    • 5 replies
    • 4,407 views
    • 7 replies
    • 1,250 views
    • 23 replies
    • 5,294 views
    • 3 replies
    • 736 views
    • 3 replies
    • 833 views
    • 4 replies
    • 886 views
    • 3 replies
    • 784 views
  • Who's Online   2 Members, 0 Anonymous, 90 Guests (See full list)

  • Forum Statistics

    20,939
    Total Topics
    249,163
    Total Posts
  • Member Statistics

    17,469
    Total Members
    1,046
    Most Online
    aviator0485
    Newest Member
    aviator0485
    Joined


  • Topics

  • Posts

    • Safely making French dovetails
      I think he's doing a stopped sliding dovetail along the length of a piece of pressure treated 4x4 that's been ripped to 3x3. @wizardgmb, does the dovetailed groove run all the way through both ends, or is one end still solid wood?   You can slap together a shop made one in a few minutes with your table saw. (feel free to message me if you're not sure how to make one).  It's worth doing - it will help stabilize the work piece and make the operation safer. Definitely remove as much of the waste as you can with your dado stack or a straight router bit, so you lessen the work the dovetail bit has to do.  That will let the wood react however it is going to when you're using a straight bit, rather than a more trapped dovetail bit.
    • Lets discuss "good" things to get from Harbor Fright
      I've been in the store a few times Steve..  Frankly, I have a hard time supporting a store that has 99% crap with a couple diamonds in the rough.  It might cost me a little more at a store genuinely trying to carry quality stuff but, I'd rather see that store stay in business so, is worth a little extra.
    • Jig saw recommendations... Bosch barrel grip?
      I recently bought the Bosch JS572EBL, which is one model up from the 470 you were looking at and I love it. It's a bit pricier but still $100 less than the Festool and you don't need an addition $200 accessory kit to get the tilt base. The only thing I've had to compare it to is a very cheap Skil jigsaw and the difference is night and day. I have medium-large hands and love the barrel grip. The cut is amazingly clean and plumb and the saw is very easy to control.
    • Milescraft Router Design Inlay Kit
      I enjoy inlay work, too.  If you find that you like doing inlay consider this..... I really like a plunge router for inlay work. It is nice to position the router and plunge the bit straight down especially when working with small areas.  It is also nice to just release the lock and have the router bit raise itself out of the work.  This reduces the chances of gouging the edge of your routed area when lifting the router and a plunge router lets you just set the router right side up on the workbench. 
    • Building the Game Table
      Holly stays white under waterbournes. Some can impart the faintest cool tint  but a base coat of super blonde shellac will counteract that. I use M L Campbell products but I have heard good things about General Finishes waterbourne finishes. Not that I think your primo wood needs any but the water based stains General makes have behaved quite well for me. Easy to handle and no smells plus reasonable prices.
  • Popular Contributors

  • Who's Chatting

    There are no users currently in the chat room