MarketPlace
694 topics in this forum
-
- 0 replies
- 5449 views
-
- 2 replies
- 609 views
-
- 13 replies
- 293 views
-
- 1 reply
- 392 views
-
- 12 replies
- 1188 views
-
- 0 replies
- 378 views
-
- 1 reply
- 780 views
-
- 4 replies
- 503 views
-
- 0 replies
- 336 views
-
- 6 replies
- 488 views
-
- 0 replies
- 290 views
-
- 0 replies
- 249 views
-
- 2 replies
- 538 views
-
- 0 replies
- 262 views
-
- 2 replies
- 434 views
-
- 1 reply
- 378 views
-
- 17 replies
- 696 views
-
- 1 reply
- 668 views
-
- 2 replies
- 951 views
-
- 11 replies
- 733 views
-
- 2 replies
- 576 views
-
- 1 reply
- 392 views
-
- 6 replies
- 693 views
-
- 4 replies
- 863 views
-
- 0 replies
- 596 views
-
Who's Online 11 Members, 0 Anonymous, 247 Guests (See full list)
-
Forum Statistics
28623
Total Topics386184
Total Posts -
Member Statistics
-
Topics
-
-
Posts
-
This morning, I was able to get the new bushings in the front axle body. It weighs every bit of 200 pounds, so I had to go carefully slow, working by myself in this isolation. I was able to roll it around on a moving dolly. I had cut up some leftover scraps of 4x6 into cribbing, figuring I could jump up each of the three "corners", one at the time, by myself. That actually worked great. I could not have done this job, by myself, safely without the cribbing. It was actually kind of fun having to figure it out, and being able to take what time I needed. Some of the cribbing blocks allowed me to get it into position at the shop press, to press in the largest bushing. I had tried to tap it in without the press, but was having an impossible time keeping it straight, and once it got crooked, there was no straightening it back out. I'd have to knock it out with a dead blow hammer, and try again. Once I got it set up on the press, the bearing went right in. The small diameter bushing on the front pivots inside another bushing in the tractor frame. The front of that axle casting was too long to get in the press, but being a small diameter, it was much easier to get lined up so I could pound it in with the 2 pound stone hammer, and some press dies. I stood it against the press, with the back end on the floor, and that went right in too. I got lucky on the big bushing in the frame, and first lick with the dead blow hammer sent it straight enough to finish with a couple of press dies, and the 2 pound hammer. Then I rolled the axle into position under the front of the tractor, installed the bell crank, and started stacking the cribbing, and jumping up each corner. It took me three hours to do all these steps, but I went back to the house to each lunch, and the main axle casting was in the tractor. I had to get Pam to come help me get the axle ends on. I could have done it by myself if I had taken the wheels off, but I called her away from what she was working on, and in fifteen minutes, we had some bolts in each side holding the axle ends on. I spent another couple of hours hooking up the new tie rod ends, and aligning the front tires. This is the first time, since I've owned this tractor, that there is no slop in the front end. The mixed up, for the second time, order of new hydraulic lines is supposed to be here Wednesday, so I might actually get to see if it all works this week. -
By wtnhighlander · Posted
People who marvel at the pyramids of Egypt have never met a woodworker with a new (large) tool. There is ALWAYS a way to "Git 'er done!" -
By wtnhighlander · Posted
Nice solution! I enjoy hearing how other folks solve problems with what they have on hand. Always a new trick to learn. -
By wtnhighlander · Posted
Thanks, Dave! Its great to have the guy who REALLY knows the answer to chime in! -
By wtnhighlander · Posted
Are you talking about keyholes in the wood itself, or steel keyhole plates? I feel like the weight may be a touch high for just two keyhole in the wood. I realize that most of the force will be down, not out, but if someone grabs a stick without paying attention, and pulls it against the retainer, it could come off the wall. I would feel better with a fastening that can be tightened in place.
-
-
Popular Contributors
