One Time Tools

Discuss One Time Tools here.

46 topics in this forum

  1. Vise-Less Work Support

    • 4 replies
    • 86 views
  2. No. 94 Dual Beam Scribe

    • 0 replies
    • 201 views
    • 6 replies
    • 329 views
  3. Rabbet Gauge Set

    • 0 replies
    • 235 views
  4. Bench Rule

    • 5 replies
    • 379 views
  5. Clamping Cauls

    • 3 replies
    • 237 views
  6. Fat Head Hook Rule

    • 2 replies
    • 179 views
    • 12 replies
    • 1288 views
    • 2 replies
    • 330 views
    • 2 replies
    • 226 views
    • 4 replies
    • 323 views
  7. Sharpening System

    • 7 replies
    • 328 views
    • 1 reply
    • 223 views
  8. Exact Dado Width Jig

    • 9 replies
    • 728 views
  9. Pocket T-Square

    • 5 replies
    • 387 views
  10. Gauge Blocks

    • 0 replies
    • 206 views
  11. Workholding Kit

    • 8 replies
    • 455 views
  12. Corner Jig

    • 1 reply
    • 256 views
    • 7 replies
    • 787 views
  13. 6-in-1 Shop Gauge

    • 2 replies
    • 1151 views
  14. Radius Quick Jig

    • 0 replies
    • 372 views
  15. Equal Space Divider

    • 4 replies
    • 1187 views
  16. DelVe Square SS

    • 2 replies
    • 1129 views
  17. Setup Blocks

    • 6 replies
    • 343 views
  18. Miter Master

    • 13 replies
    • 466 views




  • Topics

  • Posts

    • You're rolling!  The sash job, that I started over six months ago (can't remember when it was really), is still at this stage.  Not a stick has moved since then.  I got sidetracked, which is not unusual.  Those computer parts, in the background, are still there too, as well as a bunch of unopened tools still in boxes added since that picture was taken.  
    • It was a new house. The only thing that really sucked was the jointer. I guess plywood is a PITA but i don't use it all that much and when i do I break it down in the garage. Moving stuff in sucks yes, but my shop is 64 degrees year round, has 9 foot ceilings, and full plumbing. Some day we might put an addition on the house. At that time i'll add on to my shop and put in a man door or something that goes strait, and to the garage or something.
    • I went to use one of my bessey clamps a couple days ago, and suddenly my shelf was not sitting square and tight in my case. Took the shelf out, fiddled a bit, and then the gap was on the opposite corner! (I had ended up reversing the orientation of the clamp) Mine was out of square by about the same amount shown in OP’s pic. Grabbed another off my wall and it was correct- just slightly out of square in the opposite direction. I was in HD yesterday and took one of their nicer speed squares over to the clamps and one of the four 24” clamps they had on the shelf was like this. I’ll be sure to check them before I buy them in the future. 
    • Very nice, like the clean lines and the attention to detail with the continuous grain. Did you use anything to reinforce the miter joints? I'm assuming dominos but wasn't sure. I agree with you on the MCM stuff, kind of grows on you. 
    • dude I think I would have bought a new house before I moved all that in basement. or built a ramp  
  • Popular Contributors