Pete Staehling

Members
  • Content Count

    175
  • Joined

  • Last visited

Community Reputation

52 Good

About Pete Staehling

  • Rank
    Apprentice Poster
  • Birthday 06/30/1951

Profile Information

  • Gender
    Male
  • Location
    Tallahassee, FL
  • Woodworking Interests
    My current woodworking interest is primarily focused around building Mountain Dulcimers. I do also take on other projects as the urge hits me.

Recent Profile Visitors

1,895 profile views
  1. Pete Staehling

    Turning Golf Balls

    Do you have a picture of how you chucked them? Just curious...
  2. Pete Staehling

    Air Compressor

    I found the pancake model that I had to be a total fail. If I were to list it's faults, it would be a long list. Other models may be better, but I think most shops will find a need for a bigger better compressor. I have been much happier with my California Air Tools 10020C. It is quiet and works flawlessly. I have it set up to run only when the lights are on in the shop. If anything I'd go bigger, but it is a pretty nice compressor for a small shop.
  3. Pete Staehling

    Slab Flattening Jig

    One thing that wasn't mentioned... Before doing anything to the sled, I'd try just not pushing down on the router. Take light cuts and let the weight of the router provide most if not all of the downward pressure on the sled.
  4. Pete Staehling

    Pure Lee Valley Tung Oil waxy finish

    I have never seen that with the oil I use. Is it possible that it came from dust settling on wet excess oil? Maybe try wiping off the excess more thoroughly at application time and again in the next hour or two? FWIW, I use Gulf Coast Tung Oil. He is a local grower and producer of tung oil trying to revive the production of tung oil here on the gulf coast. The product is top quality. http://www.gulfcoasttungoil.com/
  5. Pete Staehling

    Worried

    Looks like not to far from the size I buy to shoot out of my slingshot. Maybe someone is taking pot shots at your shop. Just kidding, sort of any way. If I had to bet, I'd bet on a detent or similar function. FWIW, I wouldn't lose a moment of sleep worrying over it. I sure wouldn't be taking stuff apart to figure it out. Set it aside and enjoy your shop.
  6. Pete Staehling

    Mallets

    Wood, rubber, and dead blow all have very different properties and are far from interchangeable IMO. That said I'll add another choice that I use and like... I find my rawhide mallet to be very useful too.
  7. Pete Staehling

    Spindle Sander - Floor Model Recommendations

    Just food for thought, but... Things like a spindle sander or a 12" disc sander don't benefit as much from the application of more money as most tools. For example the various inexpensive bench top spindle sanders are all pretty good. Just as an example of the kind of tool that has some minimal standard that has to be met to make it a good tool... Even Harbor Freight sells a pretty nice 12" disc sander is a real work horse. I like mine enough that I have no desire to replace it with anything better. If I were to upgrade my Triton spindle sander I'd probably be thinking of getting an edge sander and even then would keep the Triton. I don't claim to know your specific usage, so maybe a real production heavy duty tool is required. I just have a hard time imagining that being the case in anything but a high production commercial shop.
  8. I have found that the lumber yards that are likely to treat you the way you describe are the ones that sell lumber mostly to the construction industry or other largish commercial customers. They are not the kind of place that I want to shop for lumber. They are usually selling big lots of lumber mostly not in the species that I am interested in. At the other end of the spectrum are places that sell hardwoods to hobby woodworkers and charge really high prices while usually having a selection of small quantities of a variety of species at a premium price. Some of these are also tool suppliers like Woodcraft. These are not my choice either. I find that there are lumber mills that have a variety of hardwoods at decent prices who sell to small buyers as a major portion of their customers. Some are a one man or family operation. Before I moved south there were a lot of these within an hour drive of home in Amish country (SE Pennsylvania). They had a great stock and were good to deal with. Prices were fair. Depending on the region they will be fewer and further between, but they should be available in your area, maybe with a day trip to shop. I don't know your area well, but a google search would likely turn up several family run or one man mills that are within an hour drive. I am sometimes willing to make an overnight trip to somewhere to lumber shop. I'd even go to Groff and Groff or Hearns in SE PA if they weren't 1000 miles away from here. I will sometimes even go that far if I can figure out a way for the trip to have more than one purpose, in my case visiting family in Maryland is a good excuse for a stop in SE PA. I might also look up sawmills when I travel for backpacking trips or other recreational activities.
  9. Pete Staehling

    New Shop Layout - Thoughts?

    If it was me I'd rather have the space open than split it that way and in those proportions. It doesn't look very workable if you will have projects of much size. I did use a wall across the back in my two car garage shop to create a 6' deep laundry/storage area. Depending on what you are storing in the other side maybe shelves would accommodate much of it and if not I'd suggest doing as I did and adding a big shed to get the other stuff out of the shop. I have 16" deep shelves floor to ceiling on close to half of the wall space and added a largish shed to get a lot of the non-shop stuff out of the shop. Between the laundry/storage room, the shed, and putting some non shop stuff on the less easily accessible shelf space I wind up with a nice workable 18'x18' space dedicated to the shop.
  10. Pete Staehling

    deepest throat (not resew) table top bandsaw

    There are some three or four wheeled bandsaws that have a much deeper throat than the wheel diameter would be with a two wheeler. I am not sure if any are currently in production or not. On the usefulness of bench top bandsaws in general... I thought when I got a bigger saw that my little 9" Ryobi cheapie one would be unused and probably be disposed of. I was wrong. While it was a very poor excuse for a bigger bandsaw, it is super handy and I use it numerous times everyday for many little light duty tasks. If it were to die I'd replace it with another bench top band saw. It is a very poor substitute for a bigger bandsaw, but is a useful tool in it's own niche, or at least it is in my shop.
  11. Pete Staehling

    Band Saw Upgrade

    Just my two cents on a few aspects of this... Not sure what $100 blade you bought, but on the 14" delta clonesI doubt that a heavy duty re-saw blade makes much sense. I found that even the thin (0.022"?) 3/4" Timberwolf blade really can't be tensioned very well on these saws. It is supposedly designed to run lower tension, but I didn't find that to really be optimum. Initially I thought they were pretty good, but ultimately I found problems. Running the necessary tension for those blades to really perform destroyed the tensioning arm on my saw in about a year of not very heavy re-saw use. I built about 100 mountain dulcimers in that year and did all the re-sawing of the sides and sound boards, so it was used a good bit but not like a production shop making furniture. I decided that a 1/2" blade gave as good or better re-saw results compared to the 3/4" one on these saws. I am not convinced that it is worth upgrading the guides to carters or whatever. I think that on a properly tuned saw the guide choices are not super critical to the cut quality. For me one key was setting up the tracking so the bottom of the gullets was in the middle of the tire or at least close (a problem with the 3/4" blades). I have found that for my work my 14" delta is fine. Maybe not ideal, but Ok. It is slower and the results might require more passes through the thickness sander than a bigger better saw would require, but for my work that is acceptable. If it was a higher production shop doing the same work I might be able to justify the expense and space taken by a bigger saw. In that case I'd want to keep the 14" saw for cutting curves and avoid changing blades on the big saw leaving the re-saw blade on it most or even all of the time.
  12. Pete Staehling

    cones

    It sounds like you are actually a segmented approximation of a cone rather than a cone. A birds mouth style construction might make sense for that, but it seems to me to be more trouble and more material used than either a sheet metal cone or a Thien type baffle, with no significant advantage over those options. FWIW, I found that the Thien baffle is very easy to build, more compact than a cone, and very effective. You might want to consider that option if you have not already done so.
  13. Pete Staehling

    Hobbyist Recommendations

    This brings up a good point. A lot of this depends on what you will be building. I typically break down my stock into about the lengths that the actual pieces will be first before jointing and have been very satisfied with my shop fox bench top jointer. I have not wished I had bought bigger or better. I have found it fine for 5' lengths, but I most often work with lesser lengths. If I were to need to rarely joint something too long for my little jointer, I'd just have my lumber supplier joint it for me rather than buy a large jointer for a very rare or one time project. If you will be frequently needing to joint longer stock that can't first be cut to length or wider stock a small jointer may not work for you, but I suspect that a lot of folks would be just fine with a 6" bench top jointer. BTW, on the width limitation I find that I often want to book match when I need wider pieces which cuts the needed width to be jointed in half. Once the glue up of the book matching is done the thickness sander quickly gets it to where I want it. Also, Different strokes and all that but, "good enough" is literally good enough. It may take a bit of extra care to do quality work on mid level or cheaper stuff, but it can be done. Personally, I require my tools and materials to pay for themselves in finished products that either would have cost me as much to buy pre made or finished products that I can sell and at least pay for my tools and materials, but preferably making a profit. That is easier to do if I keep the tool purchase prices down and don't splurge too heavily on tools. I have friends who spent many thousands on tools and have never built enough to even come close to recouping their investment on even one of their large power tools. I think that at least some of them derive a lot of enjoyment from buying and owning their tools, but I prefer to get my enjoyment from turing out nice finished work on "good enough tools".
  14. Pete Staehling

    metal one handed quick clamps?

    I have not found that to be the case. They do require a good bit of hand pressure to get them tight, but I didn't find them to be especially lacking in clamping pressure.
  15. Pete Staehling

    metal one handed quick clamps?

    FWIW, I have a pair of the Jorgenson EZ Hold ones that, if memory serves me, have lasted at least 20 years. They do have some plastic parts though.