AcworthWW

Members
  • Content Count

    23
  • Joined

  • Last visited

Community Reputation

9 Neutral

About AcworthWW

  • Rank
    Apprentice Poster

Profile Information

  • Location
    Acworth, GA
  • Woodworking Interests
    Furniture

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. AcworthWW

    Table Design and Wood Choice Sanity Check

    I appreciate tall of the comments and suggestions. We decided to do with a single species. We stopped by the lumber yard to check on the maple and wandered over to see how the walnut looked. We ended up going with the walnut. I was able to get 8/4 FAS walnut for 8.50/bf. Pretty happy with that price. It is all front he same batch so the color matches well. I will likely go Monday and pick up a few more boards to give myself some more options for grain continuity. What I don't use in the top I can use in the base.
  2. AcworthWW

    Table Design and Wood Choice Sanity Check

    I do like the idea of a contrasting dark wood on the top next to the maple. I thought about not using this board and doing a regular ambrosia top with dark breadboards. Wifey was not a fan of that idea. I ma be able to talk her into something light and dark that does not involve breadboards.
  3. AcworthWW

    Table Design and Wood Choice Sanity Check

    I did consider resawing, but I am worried that it would be too thin by the time I got it surfaced. The wife wants a thicker top and that board is only 8/4.
  4. AcworthWW

    Table Design and Wood Choice Sanity Check

    Thanks for your thoughts. I can see how it could be busy and a waste at the same time. The wife wants the table to be between 6 and 7 foot lomg. The ambrosia board is about 10 foot in length. I was going to use that in the middle and get some additioanl ambrosia for the rest of the top. My local yard has 8/4 for 3.50 bf this weekend.
  5. Hi Everyone, I am in the initial planning stages of my next project. The wife wants a new formal dining room table. We have settled on a trestle design similar to the one that Marc did on the free site. She also likes a design that she found on the Ishitani youtube channel. I already built her a figured Sapele table for the breakfast area, so we decided to go with a lighter top for this table. She likes Ambrosia maple and I happen to have a rather unusual piece of 8/4. I will include a photo below. Now we need to decide what to do with the base. We want to go with a darker wood to contrast with the top. We are thinking walnut because I also have a piece of figured walnut that could be used for the stretcher. I would like some thoughts from all of you. Does this thought process make sense? I would like to get some thoughts from all of you. The folks here have much more experience that I do with wood choice and design. I am open to other choices outside of the walnut. I appreciate your thoughts and help (I am sure that the wife will as well).
  6. AcworthWW

    Alternative to French cleats

    I have used these to hang several projects. They are low profile and give you some wiggle room during installation. http://www.rockler.com/2-z-clips
  7. AcworthWW

    Baltic Birch

    I have had good luck with Peach State Products in Kennesaw. Good selection of lumber and various grades and types of plywood.
  8. AcworthWW

    Miter gauge issue

    I checked it with a 12" combo square using the ruler against the miter gauge. That smaller square is just what I had handy at the time. I did readjust the nylon inserts to make sure there was no play in the slots. I will try removing the sacrificial fence and see if that helps. Thanks.
  9. AcworthWW

    Miter gauge issue

    I am checking the cuts with a Starrett combo square. I also used that same square to strike the line. No worries. I went back and checked to make sure that I wrote the correct number. It is within .001 and *.0005*. The digital dial fluctuates between those two numbers. That is the limit of the dial's sensitivity.
  10. AcworthWW

    Miter gauge issue

    Thanks for the replies. The first thing that I did was check the squareness of the miter slot to the blade. The gauge fluctuated between .001 and .0005. I do not think that I can get it much better than that. I made sure that all of the screws were tight and no slop in the miter slot. That is why I am at such a loss. I am not sure what else I can check or tighten.
  11. AcworthWW

    Miter gauge issue

    Good evening. I am having an issue with my miter gauge. I have an Incra 1000 HD that I cannot get square with the blade of my saw. I have a Saw Stop and have checked the squareness of the miter slots to the blade. They are within .001 on both slots. I used an engineers square to try and square the miter gauge fence with the blade. The attached photo has some shadows, but the blade and fence appear to be square to my eye. When I make a test cut, the result is no where near square. I am at a loss as to what can be the problem. I appreciate any input or ideas that you guys have. Thanks in advance.
  12. AcworthWW

    Newest One Time Tool

    Looks like those of us that missed out on the framing square the first time around have another chance. http://www.woodpeck.com/psq2016.html?_bta_tid=214700349776000619741452060481084537899702013354696371238519410769964795154921789432091&_bta_c=1l9vg1qnug7pm15075cwqt3fg0wvf
  13. AcworthWW

    How Clean on Table Saw top?

    I have had good luck using the Klingspour Sandflex blocks. They are easy to use and do not require any liquids or solvents. Just like using an eraser. http://www.amazon.com/Sandflex-Sanding-Block-3-Pack/dp/B000GACU1Q/ref=sr_1_3?ie=UTF8&qid=1464266645&sr=8-3&keywords=klingspor
  14. AcworthWW

    Question about table top attachment

    The figure 8s do look like they would be easier. If I do put them on all 4 sides, should they be installed at an angle to allow for movement? This is the first table top that I have attached and I am not sure what I am doing.
  15. Hello all. I am in the process of building a Shaker style dining table. I plan to use Z clips to attach the top to the aprons. My question has to do with the clips and wood movement. Do I use the clips on all 4 aprons or only on the 2 that will not inhibit wood expansion? I am concerned about the top expanding and bowing the aprons. The top is 42"x42" and made of curly maple and the aeons are QS Sapele.. Any advice is appreciated.