Chris H

Members
  • Content Count

    511
  • Joined

  • Last visited

Community Reputation

114 Excellent

1 Follower

About Chris H

  • Rank
    Journeyman Poster
  • Birthday 10/13/1982

Contact Methods

  • Website URL
    http://Holtzerwoodworking.shutterfly.com
  • Yahoo
    HoltzerCustomWoodworking@gmail.com

Profile Information

  • Gender
    Male
  • Location
    West Bend WI
  • Woodworking Interests
    Mostly furniture of some kind. Though I have done everything from roughing in framing to decorative jewelry boxes, to custom furniture. I like to dabble in everything.

Recent Profile Visitors

2320 profile views
  1. I ended going without a separator for the short term. Appreciate the link though. I did mount the blower directly to the top of the DDXL, so perhaps the venting was enough to slow air turbulence or I had a leak somewhere. I ended up returning the DDXL with the intent to buy into a CV at some point, but couldn't swing it immediately financially. Given the link shared, I may try the DDXL again, being extremely careful of any leaks, and then if still having issues, just adding some distance and bends between the blower and the separator.
  2. The ClearVue is substantially larger than the DDXL. I am not suggesting that necessarily justifies it, but they are pretty different.
  3. I actually had this exact problem with my HF 2HP version. I checked for leaks, so I don't think that it. Good thought though. This is a good thought, but I believe this would be tool small. Dimensions seem like they are similar to the SDD XL. I think I may be stuck either forking over the $450 to CV or building.
  4. I already disassembled and sold the old setup, and reverted the new DC to the intended formation until I can a separator figured out. So unfortunately, I don't have any pictures. I will keep this updated though as I go on the journey.
  5. I have recently upgraded my 2HP Harbor Freight unit, that had a Wynn Filter and Super Dust Deputy, with a Grizzly G0562. The original plan was just to plop the new blower on the existing setup and expand/replace the filters (ignorant in hind sight). However, I quickly found that this was much too much motor for the "Super Dust Deputy". First time I fired it up, it sucked the pipes clean as well as emptied the barrel. So the backup plan was to upgrade to the "Super Dust Deputy XL". The motor overpowered that as well. I could get the barrel to about 25% full before the chips just went right to the filter/bags. So my question for the forum is if anyone has any experience building a large cyclone, and if so, do you recommend the build or just buy? I have limited metal experience, but always willing to learn, especially on shop projects. If buy is the recommendation, any economical options out there? I can only find options online to buy the blower with the cyclone.
  6. I have both a Shelix version in my DW735 planer and the Grizzly 8" Jointer with factory installed helix cutter. The planer leaves a better surface than the jointer, but I tend to hog more off with the jointer too. I do suspect the 90 degree cutter results in a bit of extra tear out, though for me it's not enough to warrant any changes. If the cost of the aftermarket is comparable (and keep labor in mind, because it's a job to swap out cutter heads) then I'd go after market.
  7. Chris H

    New Shop Build

    I have been extremely impressed with it's performance. I have run a couple hundred board feet through full milling at this point, and there is only a 1/4 cup or so in the bag. I will keep the ratchet straps in mind though if the turnbuckles fail again. No real risk of sweating can....sadly the shop is colder than the can!
  8. You can find blast gates for significantly less than the cost of ball valves. http://www.homedepot.com/p/POWERTEC-2-1-2-in-Blast-Gate-for-Vacuum-Dust-Collector-70133/207141280?cm_mmc=SEM|THD|google|&mid=sGGzTBmKX|dc_mtid_8903tb925190_pcrid_111416414825_pkw__pmt__product_207141280_slid_&gclid=Cj0KEQiAhs3DBRDmu-rVkuif0N8BEiQAWuUJr_Fhpvw9rQvFElP6QhJecq3uvIbgR6NoEF4zYfOjgXwaAksd8P8HAQ
  9. So perhaps we are saying the same thing. Shopvac < 2HP HF Unit. Yes?
  10. I was referring to the conversion from single stage non HEPA to a dual stage HEPA unit. Basically adding a pleated felt <.03 micron filter and a separator (dust deputy). Motor strength isn't really the issue. You can surely get better DCs with larger motors, but then you are moving into significant $$$. 2HP is a pretty respectable motor for small shop DC. Most dual stages <$1k are smaller than 2HP.
  11. I think you may be drawing some false conclusions. A HF 2HP model out of the box will embarrass just about any shop vac on the market. (I am differentiating shop vac and dust extractors here.) The most important difference is not the motor, but instead the impeller. Most shop vacs are running tiny impellers, where a dust collector, like HF is running ~7"-8" (~2x-3x larger). I can't remember the sizes, but the specifics aren't important, the proportionality is what counts. HP in a motor simply represents how much load you can put the motor under, you can gear RPMs to get the speed that is ideal. This is important with large impeller, but not so much with small. Don't get me wrong, HP is good, but you cannot compare a shop vac to a true DC, the math just doesn't work. A DC will serve you much better in the long run versus a shop vac. A shop vac is designed for a short runs and small volumes at high CFM. A DC is designed for long runs and greater volume more consistent CFMs. You see the HF Frankenstein'd because folks (myself included) are trying to get higher end DC performance out of it, not because they are trying to keep up with shop vacs. Out of the box HF DC > Shop Vac for the use you are describing, plus you have the option to Frankenstein it down the road should you choose. I did the shop vac thing in my first shop and was very disappointed. Dragging a 4" flex hose around your shop will be less expensive and much greater performance than piping 1.5" permanently. 4" permanent will be a great target to achieve someday, but I don't recommend spending money on piping you will want to replace in a year or two. The cost difference between 1.5" and 4" is not that dramatic. When you want to go above 4" it gets kinda crazy, but up to 4" its pretty cheap.
  12. Here is the solution I went with, just in case someone else finds themselves in a similar situation. I trenched about 290' of Cat10 cable from the house out to the shop. Put a wifi router on the shop end, and then attached a wifi connected outlet to a strobe light / siren. All in, I probably have $250-$300 into it. I know that sounds like a lot, but this was the cheapest solution that actually worked. The 105db siren actually gets my attention better than the light. In a fully lit shop, the light is a bit useless unless you are gazing in that direction. My wife can now get my attention from the house or from two states away (she tested it when she was out of town...) Side benefit is I now have Wifi in the shop (and a good chunk of the yard around it). Here is a link to the Siren/Light. Here is a link to the wifi outlet
  13. Chris H

    New Shop Build

    I found out what the issue was on mine, and I am hoping this can help you too. Seems the sheet metal that connects the wyn filter is clipped to buckled. I am assuming this was from one of the many times I was moving it around prior to fixing it in place. Here is a pic to show what I mean:] Simply adjusting those and tightening them down has almost eliminated the problem. So I'd guess your issue is similar, in that you don't have enough resistance from the filter. Could be the clips not adding enough tension or some other gap somewhere beyond the separator. Hope this helps!
  14. It if makes you feel better, I epoxied a slab to my TS when using it as a workbench. Thankfully, it can easily be fixed with a little heat!
  15. If you do decide to go the self built method, you can use a CNC or contract out to cut a pattern template, to ensure your circles are dead perfect. You will need the qwas dogs or some other hole dog to make it work. Shouldn't cost you more than a couple bucks for the time to program your hole pattern and then punch in thickness of your router bearing and away you go. (Maybe a commercial option out there too.) This is on my list of things to do. Love the setup Llama's got going. Only mod I'd probably make is tossing some extruded aluminum rails around it and dropping some kind of rail and TS system on to get the super easy, perfect square cut all the time. Looks like you can also buy the "bridge" from EZ for $250 if you wanted to just build your own. This seems far more economical. Not sure how they $750 of value out of the rest of it to be honest.