Don Z.

Members
  • Content Count

    297
  • Joined

  • Last visited

Community Reputation

61 Good

About Don Z.

  • Rank
    Journeyman Poster
  • Birthday November 10

Profile Information

  • Gender
    Male
  • Location
    Now, there's a long story...
  • Woodworking Interests
    Boatbuilding, Furniture

Recent Profile Visitors

2557 profile views
  1. I used an acid stain that you had to neutralize after laying down. I don't see that on their site anymore, but this seems to be an equivalent: https://www.legacyindustrial.net/products/concrete-stain-and-dye/deltadye-concrete-stain.html They have three compatible sealers listed, the second one looks ideal, as well as the "soft skid" they say to use on the last coat. They have really great customer service, so you can give them a call and tell them what you are doing. There's also a forum at the garagejournal.com site that has a flooring sub-forum, and they post there.
  2. I have done it. I used the stain and clear coat from this vendor: https://www.legacyindustrial.net. I was going to epoxy, but this was a bit less expensive. The floor was in a brand new house, which limited the prep required. It was amazing. I really liked it, and it held up to driving on it, parking hot tires, melting snow, a 16 inch Grizzly planer being wheeled around on it, you name it. It could be slippery with sawdust on it. There is an additive recommended for that. Basically, you sprinkle a "sand like" finish on top as it is drying. If you like, you can decide wh
  3. Actually, the "easiest" thing to do... and probably the least expensive is to find an old Inca 710.
  4. WEST System 105 resin and 207 hardener. 207 is designed as a "clear finish" epoxy. According to their tech notes, pot life is 20 to 26 minutes, and you can apply three coats a day. Remember, thin coats, and there will be a bit of "absorption" in the first coat, so if that's thin enough, it should not sag. Their web site states: "Builders also appreciate the excellent fiberglass wet-out characteristics achieved with 105 Resin/207 Special Clear Hardener, yet it won’t drain from vertical surfaces like the very slow curing, low-viscosity epoxies." Four ounce cloth may also help sea
  5. I read it as making that final tail a "stubby" to give room for the bottom moldings. In other words, cut the tails as normal, then take that last tail and make it a half inch shorter than it used to be...
  6. You don't need the entire width to be one piece. The plies underneath will add to the strength.
  7. I would try https://woodfinder.com. It's a start.
  8. Not only will this work for many projects, but you can make something similar very easily. Find a quarter inch or so piece of steel. Angle iron will do in a pinch. Drill a 3/16 in hole. You don't even need to start with a dowel, just 8 side a piece of cherry. Use a wooden mallet. 3/16 dowel stock will come out the other side.
  9. If you really need new wheels (how far out of true are they?) contact Jesse at Eagle Tools: http://eagle-tools.com. If he doesn't have it, he'll know who does. Also, he might know the answer to your speed control question. Well set up, the saw runs very smooth. I don't know that increasing mass will help.
  10. Shannon's latest Lumber Industry Update podcast talks all about this. Check it out.
  11. I understand completely your desire to put the collection and electric in the floor. As stated, without a good understanding of your work flow, it's difficult to "predict" what you need. What I would do in your case, considering the size of the shop, is I would run a "U" pattern near the walls, with "up links" to where you think the tools will go. Add a couple of extra, but "cap" them. Add two runs to the center for the planer and table saw. Perhaps a third for a "floor sweep". Then, if you find you want to change layout to improve flow, there will probably be a nea
  12. I would consider a Butler Tray Hinge: https://www.hardwaresource.com/specialty/butler-tray-table-hinges
  13. I know a lot of people don't like the foam. But please understand that the Jen foam brushes are a bit better than the ones you normally find at the big box store. I tried them after reading about them in Rebecca Whitman's The Art of Finishing Wood. I've had great success with using them on Marine Varnish. The savings in cleaning, disposing of cleaning fluid, etc. make them worth a try. Also of note: Varnish brushes really are for varnish. If you use them for paint, they become paint brushes, not varnish brushes, so then you need a second set. If you don't varnish (or paint) often,
  14. By the box: https://www.jamestowndistributors.com/userportal/show_product.do?pid=1189
  15. I've been thinking about this. Yes, absolutely, you'll want to learn to sharpen, and keep the blades sharp as you work. I also understand your desire for economics, especially with a young one, and the fact that you are just starting out and are not sure exactly how this is going to go. Something you might want to consider is that this sounds like a good opportunity to try the "scary sharp" system. A glass plate and some sandpaper is inexpensive, and if you make it through this project and decide to stick with it, you will not have a huge sunk cost when considering an upgrade.