Chip Sawdust

Eastern Washington area

Recommended Posts

Nice! My favorite is the 140 skew block plane. It's my go to for nailing the final sizing on tenon cheeks.

That bedframe is looking awesome. Seems like there are a lot of parts there that will need finish as well.

Share this post


Link to post
Share on other sites

Thanks guys, this project has messed with my mind but I finally think I have it nailed. So to speak (glued will be more like it). 

Tonight I cut the headboard cloud lifts and sharpened a bunch of chisels as well as my shoulder plane. Messy with water stones but absolutely necessary and frankly, rewarding to see a shiny new microbevel on several tired edges. 

I made a template for final routing and shaping of the headboard legs but the footboard legs are different, as of course are the profiles for the top span. So that looks to be tomorrow's project as I near the final shaping/sanding before assembly. And I found I don't have a 1/8" rounding bit for the 1001 edges so I need to hit Woodcraft soon! 

Share this post


Link to post
Share on other sites

Messy work flattening the water stones. I wouldn't normally use the finer grit sandpaper but it's what was on my surface plate and I didn't want to change it. They weren't too bad, but now that I've sharpened more edges they need another go. 

AAE21874-5CF0-4441-BC4F-D4FA96AFC298.jpeg

Share this post


Link to post
Share on other sites

So during the summer I found this old fore plane and brought it home with me. I tried everything to sharpen it and finally figured the original bade was crap. Hock tools, do you have a... I'll be darned you do! And a chop breaker to go, I'll be darned! 

So $80 later, I put the Hock blade/breaker on the plane body, adjusted the frog a bit (the Hock blade is thicker) et voilà ! I'm making shavings! :) 

92CBE021-5481-479E-871A-56F4CA0C1484.jpeg

Share this post


Link to post
Share on other sites

Hey y’all, I’m in Spokane. I was raised here, but spent 9 years in the Marine Corps, so I ‘ve only been home for a year now. I’m still setting up my garage shop and found one hardwood dealer so far. I’m very out of practice, I took Woodshop for one year in High School, and took a couple drafting classes in college. I’m medically retired, so my back, neck, and hip can’t do what they used to and I spend more time on my couch then I would care to admit.

Right now my hold up is drywalling the walls. I have a bunch of Craigslist tools that I’ve collected this last year and space is tight. I already have the drywall, the tape, joint spackle, putty knives... etc. I just don’t have the physical ability to get drywall on the walls. If anyone has tips, tricks, or knows a handyman in Spokane that doesn’t cost an arm and a leg, I’d appreciate all the help I can get!

Any other Spokanites in here?

Jack

Share this post


Link to post
Share on other sites

Hi Jack, welcome to the forum!

Sorry, I'm too far to be of much help (TN). Doing the walls isn't a terrible chore, but ceilings are a challege for a single person, no matter how able-bodied. If the space isn't huge, I imagine scheduling a drywaller to do the job will be more trouble than raising the cash to pay. The good ones stay booked up.

Share this post


Link to post
Share on other sites
On 1/18/2019 at 9:52 PM, Jack M. Dalbey said:

Hey y’all, I’m in Spokane. 

Any other Spokanites in here?

Jack

*raises hand* Been in Spokane off and on since '81 so not quite a native but close enough. :) 

Share this post


Link to post
Share on other sites

By the way, I finished that bed I'd been working on when I signed up here. There's a thread for it but here's the finished product :) 

My lovely wife is the decorator so I can't take credit for that...

4967DD71-7964-44FC-873F-ACC1B5EECA67.jpeg

  • Like 1

Share this post


Link to post
Share on other sites
28 minutes ago, Chip Sawdust said:

Made a home made saw track for my little DeWalt saw. Works pretty darned good if I do say so myself. :) 

A99580B9-BB1A-402F-8F00-B254BE82E094.jpeg

That's the only kind I've ever used, only I always ripped a straight, factory edge off of a sheet of plywood for the guide fence.  One side works for a 7-1/4" saw, and the other for the 314.

Share this post


Link to post
Share on other sites
On 2/11/2019 at 5:34 PM, Chip Sawdust said:

Made a home made saw track for my little DeWalt saw. Works pretty darned good if I do say so myself. :) 

 

On 2/11/2019 at 6:05 PM, Tom King said:

That's the only kind I've ever used, only I always ripped a straight, factory edge off of a sheet of plywood for the guide fence.  One side works for a 7-1/4" saw, and the other for the 314.

Right there with ya.

57656889c5a73_GCS-v2ShopMade018.jpg.19dde3c5a31c5ecdba8e18d030358ec1.jpg

5765688919c16_GCS-v2ShopMade017.jpg.888eaa0ae814a5d746975a7ee937f39c.jpg

5765688793676_GCS-v2ShopMade013.jpg.48721176cec9cf6cb3f84c3823e74a0e.jpg

 

  • Like 1

Share this post


Link to post
Share on other sites

Making 3/8 mortises 1/4 apart in oak end grain used to be a fantasy. Now I can actually make them (if I need to)! 

And yes, if you look close I only locked one side of the fence, yet it stayed solid. I think I'll love this machine. 

Share this post


Link to post
Share on other sites

I might want one of those.  I have the Delta kit that fits onto a drill press.  It works OK but because I have a benchtop press it can be kind of fiddly to use if you need to make deep mortises on bigger pieces.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Who's Online   2 Members, 0 Anonymous, 45 Guests (See full list)

  • Forum Statistics

    27,404
    Total Topics
    365,009
    Total Posts
  • Member Statistics

    20,615
    Total Members
    1,529
    Most Online
    modakply
    Newest Member
    modakply
    Joined