Mike Vee

Securing a giant mirror

Recommended Posts

Hi everyone!

My wife just bought a gigantic 8ft tall mirror..... that has no anchors whatsoever and with a baby coming to join the family soon, I really have a deep seated mistrust of the damn mirror even if it's 192lbs.

Is there anything I can do/build that I can add to the frame to make sure it's stable (including adding those earthquake straps to the wall towards the top of the mirror? It's currently freestanding and I absolutely loathe the idea of a free standing giant wooden mirror.

I've attached 2 photos for reference. one is of the bottom to show how it currently "stands" and the other is the general overview of it.

 

Tell me what you think guys! I really don't know what the hell I can do to make sure it's secure and wont slip and still look clean and discrete!

 

EDIT: I just want to clarify that I want this mirror to stay on the floor, but I want to make sure that it doesn't slide over the years and in case of any earthquakes we might experience. I do not plan to have it hanging off the wall at all, but would like a way to secure it to the wall but still be on the floor.

20190112_132728.jpg

20190112_132710.jpg

Share this post


Link to post
Share on other sites

See if you can find a couple of black iron brackets that attach to the wall and hook over the top of the mirror. 

  • Like 1

Share this post


Link to post
Share on other sites

Is there any recess in the back that you could install a French cleat to?  That plus strapped should be solid

  • Like 1

Share this post


Link to post
Share on other sites

I would find some really strong "L" brackets, and put a pair under the bottom, and a pair on the top.  A good stud finder, to find the middle of the studs, would be very good to have.  The parts that screw to the wall can be hidden behind the mirror, and if you can find some that don't come out past the face, they shouldn't be that noticeable.  Just leave about 1/16" extra height between the brackets, than the height of the frame, and it shouldn't be too bad to get it into place, but still work fine.

edited to add:   a google search for   "heavy black angle iron brackets"  found many, such as:

https://www.mudsupply.com/Simpson-Strong-Tie-HL33PC-Heavy-Angle-p/3567.htm

  • Like 1

Share this post


Link to post
Share on other sites

We have a mirror that's about that size - 98' x 42". Heavy as you know what. Ours has turned feet that keep the back about 1 1/2" off the wall. I found some aluminum C channel that width and drilled some holes through one side for screw access for mounting it to the wall. Then I cut keyholes into the front face running vertically with the large end up. The opening was about 3/4" higher than the screws I ran into the back of the mirror frame rail. I had a buddy help me lift it and put the screw heads into the keyholes and let gravity do the rest. It took a couple of tries and a few beers after, but the mount is hidden and it holds really well.

  • Like 1

Share this post


Link to post
Share on other sites

The back of the mirror is almost completely flat. Taking a look through it makes me think that the wood around it is, as you see, a frame. the rest is like how picture frames are made: a thin wood board in the back where the glass is sandwiched inbetween. backing is secured by a whole host of small screws.

I should probably mention this is the product:

https://www.crateandbarrel.com/stilt-floor-mirror/s214982?st=stilt

 

I'm assuming that I should be able to screw into the frame without fearing of damaging the glass.

I did notice that the top has an additional bar of wood that is used to keep the top edge of the frame from touching the wall. I think I can use that as 1 of the mount points (like Brendon_t's suggestion on a french cleat) especially if i can adjust the bar to be at a slight angle.

 

@Brendon_t I like the idea of the french cleat, but is there a way to install a french cleat at an angle? with a protrusion? since this type of mirror is supposedly the type that you're supposed to set it at a slight angle

 

@Tom King I'm having a bit of trouble visualizing what you are saying. With an L bracket, how would it secure to the wall if one side is already secured to the frame?

 

@Mick S ah that's a pretty cool idea. secure and inconspicuous. I have to consult w/ the wife as to how far out she wants it but I have a suspicion that she probably wants it 8" from the wall at the bottom.

Share this post


Link to post
Share on other sites

I have a large wall-hanging mirror, three pieces that hang together to resemble an arched window. I cut a sheet of 3/4 ply to match the shape, painted it to match the frame, and cut a slot in the ply, wide enough to cover 3 studs, and beveled to form a french cleat. Made the mating part from ply, assembled the thing on horses, then hung it on the wall as one piece. Rock solid.

I also have a tall book case that sits on the floor, but has a french cleat up top to prevent tipping. You might need a beveled spacer behind the cleat to angle the mirror how you like, but it should work.

If it were me, there might be an 'accident' that resulted in sweeping the thing out the door in pieces.

Problem solved.

  • Haha 1

Share this post


Link to post
Share on other sites

hahaha that is a $1k accident that would hurt me in the wallet.... and probably send me to sleep in the guest room for the rest of the year. (and well.... you don't want a pregnant woman to be angry.. they're terrifying)

I think I might be able to figure out a french cleat for the top. I just need to figure out the angle and make sure it spans as many studs as I can possibly get. I've never done a french cleat before.. but I'm sure I can figure it out somehow (Youtube is a trusty partner in this hahah)

  • Like 1

Share this post


Link to post
Share on other sites

Mike,  To answer your question,  I would install four of those brackets where they need to go-two at the bottom, and two at the top.  Then slide the mirror in place, and install some screws into the frame to hold it.  I wouldn't trust any part of that frame to hold it on its own permanently, such as a French cleat attached to the top.

  • Like 1

Share this post


Link to post
Share on other sites

I'd probably just build a frame to sit behind it so that the mirror is supported along the total height (or at least a few points rather than just the bottom and top). It would be slightly recessed on the sides and top so that it wouldn't be visible in normal use. The frame could be secured to the wall studs at various points along the height and width. It could have a ledge for the bottom of the mirror to sit on so that all the weight isn't just on the back edge, though depending on the angle your wife chooses, this might not be practical or necessary. Then the mirror can be secured to the frame with some z clips or figure 8s into the solid parts of the frame, or some small L brackets depending on space available.

The angles and total height of the frame can easily be found by making a plywood template of the side profile of the mirror frame (~3" wide, 81" long/tall). It doesn't have to be hurricane-proof, just stable enough that it won't tip or get knocked over.

  • Like 1

Share this post


Link to post
Share on other sites

It appears that the mirror is designed to sit on the floor, which also seems like the most stable situation, anyway.  Rather than trying to hang it, I'd keep it on the floor and just go with one or two of those anti-tip straps at the top, anchored to studs.

  • Like 1

Share this post


Link to post
Share on other sites

Yes, the mirror is indeed designed to sit on the floor. 

It looks like I wasn't too clear in my original post. I do want to leave it sitting on the floor. i just want to secure it in a way that it will not move at all. My biggest concern is that even though it is designed to sit on the floor, the bottom edge is not made to sit on a floor at all, which is why I am afraid of it eventually sliding. The other part that I wanted to do is to find a way to put some barrier between the frame and floor since it's a hard edge to the bottom and if i can atleast secure the mirror so it doesn't move, i can add felt pads or whatever to the bottom so that it won't damage the floors over the years.

Share this post


Link to post
Share on other sites

J bracket in slot cut in the bottom. L bracket set to screw hidden on the top. Screw the brackets to a stud on the wall. Set the mirror. Lock the top with a screw through the L.  Looks like black metal would hide well. 

  • Like 1

Share this post


Link to post
Share on other sites
49 minutes ago, Mike Vee said:

Yes, the mirror is indeed designed to sit on the floor. 

It looks like I wasn't too clear in my original post. I do want to leave it sitting on the floor. i just want to secure it in a way that it will not move at all. My biggest concern is that even though it is designed to sit on the floor, the bottom edge is not made to sit on a floor at all, which is why I am afraid of it eventually sliding. The other part that I wanted to do is to find a way to put some barrier between the frame and floor since it's a hard edge to the bottom and if i can atleast secure the mirror so it doesn't move, i can add felt pads or whatever to the bottom so that it won't damage the floors over the years.

I guess I'd use straps at the top and 3 or 4 of these things near the back edge on the bottom:

https://www.homedepot.com/p/Everbilt-1-in-Heavy-Duty-Anti-Skid-Surface-Pads-4-Pack-49644/203661092

 

  • Like 1

Share this post


Link to post
Share on other sites

If it’s sitting on the floor then all you need is to add a couple brackets/ties/whatever attached the top outermost studs and a couple spacers w ties/ screws /etc to the baseboard on each side . Adding cushions/bumpers/rubber feet is only needed if it’s a smooth floor. 

Share this post


Link to post
Share on other sites

We bought a bookcase a few months back to put in my son's bedroom.   It was 7' tall, and to secure it to the wall all it came with was a couple of d-ring hanger's like you might use on the back of a picture and a zip-tie.   Find the stud... mark back of bookcase with tape... screw one hanger in, then screw the other into the stud so the rings line up just above the bookcase and zip-tie them together.

When you think about it... it's setting on the floor, totally supported.   All you want to do is keep it in place.   It doesn't take much, you just want to keep it from shifting.

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now