Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

A Simple Varnish Finish DVD - variations on technique for smaller surfaces

Featured Replies

Hi all, I'm relatively new to finishing and bought the DVD last week since I have zero experience with varnishes.

I started out doing Tru Oil finishes on the back of maple guitar necks, but I could never get the results I wanted. I would typically get streaking and a whole list of other problems. Bottom line - the first few coats would always start out well, but I could never get the eventual film build I wanted without unsightly problems. Some research clued me in that Tru Oil is really just a long oil wiping varnish - that led me to looking at possibly better choices, which led me to TWW and the excellent DVD (kudos Marc).

The DVD cleared up a lot of confusion for me, esp. the idea that the pad needs to be pretty darned thick to prevent finger pressure telegraph creating the wiping streaks that were driving me nuts. Once I followed that advice, wiping streaks were gone and never returned.

One quick modification I'll mention, though, is that if you are working on smaller surfaces than a typical midsize-large tabletop, a really thick pad may soak up so much varnish when you dip it to charge it that you will never be able to spread it thin enough to get the typical desired results of a wiping varnish. For the first week of practice on 8" x 12" test panels (quite a bit smaller than the 24" x 24" flame maple block that Marc uses in the DVD), I was getting large bubbles drying in the finish, and sometimes the dried film hadn't leveled.

I started trying a few changes to help with my smaller surface, and here's what I would advise (use any or all of these as your results warrant):

1. To make your pad, use a two ply stack instead of three ply as Marc uses in th DVD. He does mention a two ply as one possibility, but he actually uses three, which seems correct for his surface. But for smaller surfaces, two ply seems to discharge the correct amount of wet film to prevent bubbling and leveling problems. I haven't seen any wiping streaks come back since switching to 2 ply.

2. Only dip the pad about 1/4" or less into your secondary container of varnish, and don't leave it in there long enough to soak up excessive liquid. I found that 1-2 seconds is ideal. In the DVD, you can clearly see that Marc dips his pad deeper into the liquid, which is correct for the size of surface he's working on, but probably too much for a smaller surface.

3. Per the DVD, if pre wetting the surface of the pad with mineral spirits is ideal for aiding the correct amount of liquid soak/charge and then discharge/flow/level onto the wood surface, it seems to me that what you are essentially doing is thinning the wiping varnish slightly with mineral spirits before applying. I haven't exprimented with this yet, but I may try just thinning the wiping varnish 10-15% with mineral spirits instead of having to create another container/step in the wiping process (FYI I'm using General Arm-R-Seal). I will say that so far, I am following Marc's recommendation of the pre-wet with MS and it's working fine.

Some of these suggestions may be obviously simple to an experienced finisher, but we all have to learn somehow, right? ;) Varnish is a relatively simple finish that neverthless has some very specific application requirements, and there's a glut of misinformation out there that really frustrates beginners who may give up too quickly, thinking, "Geez, if this is so simple as everyone says, why can't I get it right????".

That was almost me before I bought the DVD. I'd strongly recommend it to any novice finisher; you can just read bullet points and save your $25, but actually seeing Marc perform the steps is much more instructive and will save you about 2-4 months of guesswork and trial & error. Wish I'd known about the DVD sooner, would have saved myself that 4 months of failed experiments.

Last side note, I used General Arm-R-Seal per the DVD. I have also experimented with Pratt & Lambert #38 (thinned 50% since it's not thinned in the can like Arm-R-Seal), and the dried color results between the two are practically identical (I dropped a spoonful dollop of each on a white test panel and let dry for a week). Dried, both are mostly water clear with a *very* slight yellow tint (and I mean very slight, barely detectable).

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.