Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Help with Arm-R-Seal and Seal-A-Cell

Featured Replies

I have built a dining table out of cherry wood and the plan was to apply a coat of Seal-A-Cell to pop the grain a bit and then to apply a few coats of Arm-R-Seal (2 coats gloss, 1 coat satin).  I applied the Seal-A-Cell (SAC) 2 days ago.  I applied it with a rag on the table base, but because I needed to cover a large area, I used a foam brush on the table top.  The table base where I applied it with the rag looks fantastic.  I thought I had applied a thin coat on the table top, but when I went back a few hours later, you could obviously see certain shiny spots where it was thicker, almost like the poly part of the SAC had pooled.  I now realize I definitely should have wiped it with the rag immediately afterwards to soak up any excess, but too late now. 

I assumed these raised shiny areas would be very noticeable when the next coats were applied.  Advice I saw online said to give the table top a day or 2 to cure and then sand it back to smooth with 220 grit sandpaper.  I have done that, but there are still some shiny spots scattered about.  I didn't use any stain or dye on the table, but there are a couple of places where the SAC coat is much thinner where I had to do some heavier sanding to smooth out the pools.

Any suggestions on how to proceed from here?  Am I OK to start applying the first coat of Arm-R-Seal (ARS)?  Do I need to get rid of the remaining shiny spots or, as long as the surface is smooth, they won't be noticeable under the other coats?  Will the ARS even the coloration out in the places where I sanded through some of the SAC, or do I need to wipe on a second coat of SAC?  Or do I need to sand the whole thing back to bare wood and start over?

Thanks in advance!

  • Author

Thank you for the response!  I took your advice and applied a thin coat of SAC and it looked great!  Now I'm in the process of applying the ARS.  I may be applying it too thin - I'm on the second coat and still have a few small areas where it seems the wood is still drinking it up.  I think I'll need more than 3 total coats at this rate.  But I think it is going to come together in the end.  Thank you again for your help!

  • 2 weeks later...
  • Author
  • Popular Post

To update, I applied 3 coats of Gloss ARS and have now followed that up with 3 coats of Satin ARS.  Pictures are as of today.  Will hitting the top with steel wool or a brown paper bag in a week take care of those streaks or do I need to do something else?

I appreciate the advice!

IMG_1760.jpeg

IMG_1759.jpeg

IMG_1757.jpeg

  • Popular Post

The table top looks great! The only thing I can make out as possible 'streaks' appear to be brush marks. A foam brush can act a bit like a squegee, leaving 'wakes' of finish off each corner as you take a stroke. Usually, ARS cures slowly enough to self-level, but in some conditions, it doesn't. I usually apply with a rag saturated in mineral spirits to avoid this, and do several coats.

If such brush marks ARE what I see, they can usually be felt as ridges under a light touch. If so, it may require wet sanding with 1000 grit or more to smooth them away and get a buffed finish. Let the ARS cure for at least a couple weeks first, preferably a month. Fully-hardened finish sands out much better.

Maybe someone with better eyesight can tell more....

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.