Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

How long should the burr on a cabinet scraper last

Featured Replies

Subject line basically says it all, but to be more specific. I'm currently scraping an old desk from under a few gallons of poly. My scraper is an old #80, sweetheart stamped on the blade. Sharpened and burred it scrapes really nicely but I find I'm having to stop frequently to redo the burr (about every five to ten minutes or so). I realize the answer obviously is it varies, and I'm sure it's going to lose the burr a lot quicker going through thick poly than if it was just running across wood but that span seems rather short to me. The cabinet scraper only cost me a couple of bucks at a flea market, and while the body is in great shape (now that cleaned it up) I'm wondering if the blade's maybe gotten soft or something. Is this more or less normal usage in this scenario?

I just did something similar.

http://www.vitalbodies.net/site/lifestyle-diy/lifestyle/412-antique-writing-desk-library-table-or-bust.html

I used a new card and new burnisher.

I had to resharpen every five minutes or so also.

In this video:

http://thewoodwhisperer.com/scraper-sharpening-w-william-ng/

After all the grind stone stuff he shows a super fast way to sharpen the card.

I got to where I could re-sharpen in perhaps 10 seconds or less.

I used that method the most for speed.

I am new though, so some of the experts might know other stuff.

At some point I will have do the grind stones however.

  • Author

The blade I'm using is the thicker blade from the cabinet scraper but it's probably in line (I noticed my card scrapers lasted about the same length of time as well). Sharpening's pretty quick, so that part was pretty good, but like you I haven't done a lot of refinishing work in that end so wasn't sure if it was a normal time. I knew the thick poly finish that was on it before would dull quickly but that was quicker than I expected :).

Very nice desk btw.

You are probably pushing the cabinet scraper beyond its limits and intended purposes. It might be better to use a carbide paint scraper first to remove the bulk of the old finish, then use the cabinet scraper to clean up the mostly bare wood. Also, I'd consider a chemical finish stripper to remove the old finish. I've been using SoyGel, a low odor product, for a few years with great success.

I've got two vintage #80's that I use. I sharpen both then I can switch when one gets dull. Even then, I use some kind of preliminary scraping or planing tools before I go to the cabinet scrapers.

  • Author

I decided against stripper as my dad had refinished the desk a number of years ago. He was a belt sander fanatic and I was afraid it would cause veneer damage. The carbide paint scraper may be a good choice though for preliminary work to get the poly off. I got the 80 and an 81 in the same lot, I do need to fix the 81 though, the rosewood is shot. All I need to do is replace the base and it'll be good to go

I may try that SoyGel on an unobtrusive part to see how it'll work as well. Still it's a good learning experience.

I will say mine dulled from the wood at or about the same rate as the finish. Your image link is broken.

  • Author

Your image link is broken.

Weird it's my own image website :). Gremlins got in and broke it, should be fixed now.

Images link works now. Lucky for me I do not have to worry about veneer on this project, but some of the next ones I will.

You are probably pushing the cabinet scraper beyond its limits and intended purposes. It might be better to use a carbide paint scraper first to remove the bulk of the old finish, then use the cabinet scraper to clean up the mostly bare wood. Also, I'd consider a chemical finish stripper to remove the old finish. I've been using SoyGel, a low odor product, for a few years with great success.

Ditto.

Addendum: My Stanley #80 Cabinet Planes are set up with square blades measuring 2 1/2" x 2 1/2". I sharpen all four sides of the blade at one session. It is easy to reposition the blade as needed when performing work. Some times I'll set up opposite edges of the blades for different purposes, such as proper burrs for smoothing and chisel edges for glue scraping.

Blessings.

  • Author

I sharpen both ends of my #80 at a go yeah, and they're easy to reposition. I just hate having to re-sharpen that much :). Thanks for the suggestion on the SoyGel, I picked some up the other day, tried it on an unobtrusive part and it seems gentle enough to work without causing much concern on the veneer and it's glue.

  • 3 weeks later...

If you are having an issue with the burr burning out to fast, though on poly a scraper will dull quickly, it may not be dulling but breaking off. If the burr is to large the pressure of the cut can snap it off. It is more effecient to produce a sharp burr that is short. Vintage steel scrapers are also softer then modern ones, they can also be thinner steel. My suggestion would be to get a new thicker blade, tune it up well and put a small sharp burr on it.

Cheers

Hans Christopher

  • 5 weeks later...

burnishing tool ??. i think i have one that i found at a garage sale? how do i know if its not to sharpen a knife blade? or are they the same tools to use? i tried it on a pizza cutter where it did not have a bur and i made a burr? what should the steel look like?

burnishing tool ??. i think i have one that i found at a garage sale? how do i know if its not to sharpen a knife blade? or are they the same tools to use? i tried it on a pizza cutter where it did not have a bur and i made a burr? what should the steel look like?

http://www.vitalbodi...rd-scraper.html

I put some (High Resolution) images of a burnisher I used on my web site.

I think the main requirement is that the burnisher is harder than the scraper.

There is more to it than that, like they say never use a screw driver.

You might post an image of your garage sale find for the experts to see.

I think the knife blade tool has ridges and the card scraper burnisher does not.

http://www.vitalbodi...rd-scraper.html

I put some (High Resolution) images of a burnisher I used on my web site.

I think the main requirement is that the burnisher is harder than the scraper.

There is more to it than that, like they say never use a screw driver.

You might post an image of your garage sale find for the experts to see.

I think the knife blade tool has ridges and the card scraper burnisher does not.

thanks vital bodies! mine does not look like that it has like grooves and ridgers in a diaganal pattern somewhat- so i should not use it for a card scraper??

thanks vital bodies! mine does not look like that it has like grooves and ridgers in a diaganal pattern somewhat- so i should not use it for a card scraper??

linkmx674: I would not use that. You really need the smooth kind. I think you would ruin the card scraper with the groved kind. You want to create a bur by "pulling the metal out" with a burnisher.

I would think the grooved kind would not do that.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.