Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Co-planer table adjustments on a used Delta DJ-20 jointer

Featured Replies

I've purchased an older model Delta 8" DJ-20 jointer that needs a bit of a tune-up.  I watched Marc Spagnuolo's video #118 http://www.thewoodwhisperer.com/videos/jointer-setup/ on Jointer Setup and while it seem a bit tedious :) I get the importance and understand the information presented (luckily I already have a "A-Line-it" multi guage).  However, I don't see the bolt head that he used to adjust the infeed and outfeed tables on my DJ-20.  If your not sure what I mean, please fast forward to 14:35 in the video for what I'm talking about.

 

I've downloaded a copy "instruction manual" from the Delta Machinary site (google "Delta DJ-20 Manual" and it's the first result).  But, I don't see anything about how to adjust the in and out feed tables if they become out of alignment (or "non co-planer").

 

Can anyone tell me how to do this, or give me a link to some information (or possibly a video) of someone doing this?

 

 

 


 

The instruction manual doesn't cover how to adjust the beds for being co-planar.  You can contact Delta for the instructions.  Here's how it is done:

Each bed is attached to two steel rods running perpendicular to the length of the bed and they can be seen from the front or back where they sit in eccentric bushings.  To adjust the beds, you need to loosen the set screws that lock the bushings in place, then rotate the bushings to raise or lower each corner of the bed.

  • Author

The instruction manual doesn't cover how to adjust the beds for being co-planar.  You can contact Delta for the instructions.  Here's how it is done:

Each bed is attached to two steel rods running perpendicular to the length of the bed and they can be seen from the front or back where they sit in eccentric bushings.  To adjust the beds, you need to loosen the set screws that lock the bushings in place, then rotate the bushings to raise or lower each corner of the bed.

 

I've done several more "googles" on the topic, and it seem like I need to use an allen wrench to loosen the each of the *four* (correct me if I'm wrong here) eccentric bushings.  Then I need something akin to a spanner wrench or a pen wrench to adjust each one of them.  I've read on one forum where someone made one out of oak and an old allen wrench he cut in two pieces.  I read someplace else that he could turn them by hand (might be a stronger guy than I am).

 

 

I have ordered the following to try and get the job done.  

 

http://www.amazon.com/Pittsburgh-P33554-Adjustable-Pin-Wrench/dp/B001RMK2HQ/ref=cm_cr_pr_product_top

 

http://www.leevalley.com/US/wood/page.aspx?p=50074&cat=1,240,45313

 

(I'd been wanting a better straight edge, but it still hurt a bit at 85.00)

 

I'll post back if it all works out.

 

If anyone has another thoughts or advice, please let me know.  It will probably be about a week before I get the orders in and have the time to play with it.

You need a hex key/allen wrench to loosen the set screws that lock the eccentric bushings in place.  Instead of a special spanner, I used a square punch and hammer to rotate the bushings.

  • 11 months later...

I've done several more "googles" on the topic, and it seem like I need to use an allen wrench to loosen the each of the *four* (correct me if I'm wrong here) eccentric bushings.  Then I need something akin to a spanner wrench or a pen wrench to adjust each one of them.  I've read on one forum where someone made one out of oak and an old allen wrench he cut in two pieces.  I read someplace else that he could turn them by hand (might be a stronger guy than I am).

 

 

I have ordered the following to try and get the job done.  

 

http://www.amazon.com/Pittsburgh-P33554-Adjustable-Pin-Wrench/dp/B001RMK2HQ/ref=cm_cr_pr_product_top

 

http://www.leevalley.com/US/wood/page.aspx?p=50074&cat=1,240,45313

 

(I'd been wanting a better straight edge, but it still hurt a bit at 85.00)

 

I'll post back if it all works out.

 

If anyone has another thoughts or advice, please let me know.  It will probably be about a week before I get the orders in and have the time to play with it.

My bushings (had the setscrews removed) were caught in rust and would not budge. Tried a cold chisel but it damaged the notch. I made a spanner wrench (2 hours work) using a big washer, boring holes perpendicular to the disk and tapping in 10-32 SS screws. Then grinded them square leaving 1 1/4 inch between the lugs and bolting a hardwood handel to it. That did not give enough grip to the bushings. So I poured WD40 in the setscrew holes and around the flange along the body and went to sleep! Next morning I used Visegrips (ugly but last resort) and succeeded in unlodging them. I had adjusted them when I retrofitted the head with a Helix head around 4 years ago. The shop is not in a humid area. Bad design, there should be oilite bushings in there. The Powermatic has a hex flange so you can use a socket wrench! It took 4 hours to adjust the infeed table. There was .040" diff from the in to the cutterhead ones.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.