Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Air Compressor and Air Tools in Finer Woodworking

Featured Replies

Do you fine woodworkers use air tools?

 

My El-cheapo compressor went kaput.

 

Generally speaking I use the Compressor for my Nailers and outdoor projects. I dream of becoming a finer woodworker with time (Time is the key, well knowledge, but time is bigger hurdle with two small ones and a 40year old house that wasnt built right to begin with) and am planning on buying a nice compressor. Well mid-range, not top of the line but not bottom feeder stuff.

 

The point is, I know what I need for my main uses, which for the most part is 80% nailguns, and 20% other, impact wrench, filling tires, etc.

 

But is there an application in the wood shop beyond nail guns, like spray guns, sanders, other ?

 

Best Regards,

Thanks for your time and input.

 

Since posting I started reading this thread:

my questions aren't really answered in it, but it does give me an idea that some woodworkers do use longer running, high volume type tools.

 

But I am still interested in some applications of various tools from those taht would like to elaborate.

Spraying and sanding are both handy but you need alot more compressor than you would with nail guns. You also need a water separator. You can spray LVLP with a smaller compressor not a little pancake but smallish. Sanders need a lot of air and are very hard on piston compressors. I have a 5 hp 80g industrial and would not try to use my air sanders with it. For spraying and sanding I have a dedicated rotory screw. I use a little emglo contractor compressor for staples and pin nailers, it will spray LVLP pretty good but thats about it.

I always use my compressor for nail guns when doing fine woodworking. If I hand-drive fasteners, it no longer looks like fine woodworking.

I always use my compressor for nail guns when doing fine woodworking. If I hand-drive fasteners, it no longer looks like fine woodworking.

 

For fine woodworking I prefer a 22 caliber concrete nailer. :)

If you are in the process of buying a compressor to cover all your shop needs, don't listen to what I am going to say here.  :)

 

The compressor I have had for years is a PC 6 gallon pancake compressor.  Then a few years ago, I started trying shellac, and was recommended to try spraying it. Someday I would like to get an Earlex 5500.  Before wanting to spray, all I ever use my compressor for is nailguns (much less now too as I challenge myself to not use fasteners) occasional inflating, and for blowing dust out of my way.  So I don't really have a need for a bigger compressor, and would much rather put money into the Earlex.  That said, I have other tool buying priorities first!

 

So, I did a little homework, and looked into the WoodRiver sprayer.  I focused more on the CFMs then anything.  After consulting the manual on my compressor, the CFM at the low end of the PSI, the numbers weren't too far off.  SO knowing it MIGHT work, but then MIGHT not work, I decided to by the sprayer and give it a try.  To my surprise, it worked fairly well!  I was able to get a good even spray on to my project, albeit a small project.  The next project I tried it on was a cradle, which was a bit bigger.I found if I was careful, and didn't try to do too much at once, the compressor motor would keep up with me.  On that note, the compressor ran, a lot.  The manual on my compressor recommends that the motor not run more than 30 minutes out of every hour, as the motor does create a lot of heat while running.  Therefore care has to be taken to give the motor a chance to cool off as well, otherwise there is risk of burning out the motor.

 

Would I recommend this setup to someone who is buying a compressor for finish work among other things, not at all.  However if you already have a pancake compressor, and limited budget for either a dedicated sprayer or larger compressor, for small to mediumish size projects, it can work.

 

I will add, that in your investigation, ask yourself what you are going to use compressed air for.  If it is largely nail guns and spray finish, it may be more economical to get a small compressor for the nail guns (they don't need much air at all) and a dedicated HVLP system like the Earlex 5500.

1. Use mine mostly for applying a finishing, not for sanding.

2. Shooting pin nails.

3. Blowing saw dust off of out of machines.

 

-Ace-

I will add, that in your investigation, ask yourself what you are going to use compressed air for.  If it is largely nail guns and spray finish, it may be more economical to get a small compressor for the nail guns (they don't need much air at all) and a dedicated HVLP system like the Earlex 5500.

 

IMO your better off with a decent LVLP gun than the earlex. While the earlex is fine if you have no air, a good gun is much nicer than the earlex bleeder. LVLP guns are generaly affordable and use very little air.

I use a lot of pins as locators for parts like moldings...  They end up INSIDE the item, with no holes to fill.

 

- Leave the pins proud as you shoot a few where the part will be installed

- Clip them off ~ 1/32 to 1/16" high

- Press the parts together in perfect alignment

- Disassemble and apply glue

- Place molding and clamp or tape

 

When the moldings are reinstalled, the pins prevent sliding and creeping in the wet glue. 

 

Pins and brads are also very useful in many situations where there are cross-grain interfaces and movement needs to be allowed.  

 

I think the mentality that "fine woodworking" precludes using everything at your disposal to create a quality item is horse poop...    :D  Unless you're building a historic reproduction, it's one thing to fire brads all over the piece and cover them with filler that will probably be visible, but quite another to wisely use what is available to us in modern times.  Of course, for jigs, shop projects, cabinetry, and carpentry work...  Nail guns are incredibly efficient. 

 

Compressors can also clean things with a blow gun, drive veneer vacuums, inflate things, and spray finishes.  I have a great HVLP rig, but I still use a Critter on occasion because it's so much easier to clean up.  I have various air hoses hanging near machines.  A great example is when you're cutting a bunch of parts in a sled...  A quick spritz of air keeps the sled and stops clean.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.