Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Getting my shop space laid out

Featured Replies

I am getting started with a pretty small shop space and I wanted to get some advice on what I should think of in terms of layout.

 

I am slightly over half of a long one car garage. The max space I can really claim at this point is 17x10. At one end of the space is the garage door, and the in the middle of the 17' wall adjacent to the house is a door leading inside.

 

As of now, the only free standing items I have to worry about are a table saw and a jointer. The tablesaw has a mobile base and can wheel around (I have rather enjoyed using it in the driveway during nice weather). I am planning to put casters on the jointer so that I can likewise wheel it outside, or around the shop. I also have a 5' x 2' work bench pushed up against what is roughtly the middle of the uninterrupted 17' wall.

 

In terms of bench top stuff, I have a 14" band saw, drill press, and compound miter. Half the time I end up setting these on wide topped saw horse or the table saw (my bench seems to always be too cluttered).

 

How feasible would it be to set up a dedicated station for the benchtop tools? I also have a nice old stanley grinder that I'd like to mount somewhere, but don't want it on the wood bench.

 

The back half of the garage is all steel shelves full of stuff. My wife is starting to worry about the dust so I'd like to figure out a dust collection solution that can deal with slightly mobile tools.

post-13757-0-85935700-1365168769_thumb.j

When I see people in garage shops, I think it works mostly in their favor to have their saws in front of the garage door so you stand between the saw and door when you feed.

You won't need the door open to make cuts, but just incase you do, you can open it up.

  • Author

PG, I have my saw facing the other way, so that when I flip up the outfeed table it doesn't block the bench. If I were ripping something over 6' I would need to open the garage door. Is there an advantage to feeding in vs out?

 

Thanks for chiming in.

PG, I have my saw facing the other way, so that when I flip up the outfeed table it doesn't block the bench. If I were ripping something over 6' I would need to open the garage door. Is there an advantage to feeding in vs out?

Thanks for chiming in.

Im in a basement, so I really wouldn't know. I'm just saying what I normally see with people in garage shops. I could see it working either way though, to be honest.

Im in a basement, so I really wouldn't know. I'm just saying what I normally see with people in garage shops. I could see it working either way though, to be honest.

 

From the door saves on your back if you cut sheet good on your saw. This morning I ripped 40 sheets of plywood without lifting any. I feed right from my trailer onto the saw. 

If you dont use the saw for sheet good the the other way around may be best. You can go from truck to your outfeed to break down with a circular saw.

Really just depends on how you work. Im sure you will end up changing it around a few times until you find what works best for you.

Giving advice on shop layout is difficult and generally unhelpful.  Every space, tool collection and personal workflow is different...just too many variables to offer a generic "best way."  There are some basic tips to keep in mind: try setting up in a way that minimizes the need to move tools around; try setting up in a way that you're able to work on 8' material; try to keep all your surfaces the same height, etc.  But it's too complex and too full of personal choices, IMO, for anyone to be of any real help.  Shop layout is an evolution, and you'll be moving stuff around for years as you add tools and your workflow habits change.  Baby steps...

  • 1 month later...

On the table saw question.  I have done it both ways, but personally prefer feeding from the garage door in. I find that the space by the door is normally kept clear, and the space on the other side isn't, so feeding the other way means having to carry material around other tools/equipment and creates more work.

 

Also.  If I might suggest, put your work bench on wheels so you can wheel it around and use it as an out feed table. Mine is more of general (and still in basic stage) work area, but it's been perfect.

20121218_110615.jpg

I'm in a similar situation. I have mine set up so i'm feeding toward the door. I just have a small job site table saw so I don't even dare to cut full sheets of plywood on it. So i end up bringing everything into the shop and then cutting it down. But I'm still in the early phases of my shop and when I get more tools I have no idea how it will change

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.