jg9522 Posted March 3, 2015 Report Posted March 3, 2015 Hi all, I have a problem that I doubt that anyone can help me with, but I need a shoulder to cry on. About 6 months ago(maybe longer), I purchased a Carter AccuRight Ratchet Rod bandsaw tensioner. It took me a couple months to get around to opening the package and installing it. I first used it on a 1/4" blade and it worked great, and made tensioning the blade much easier on my Delta 28-203 14" bandsaw. However, a month or so ago, I put on my brand new 1/2" Woodslicer blade to do some resawing. And it took alot of tensioning to get the blade as tight as needed. The Ratchet Rod made the task much easier than it would have been without it. Midway through the cut a I heard an incredible noise, BANG!!!, then heard more noise that wouldn't stop until I frantically hit the stop button on the saw. What had happened was, the bottom of the tension rod slipped off of the semi-rounded frame of the saw and slid down between the back of the frame and the top wheel housing. It bent the ratchet rod, and trashed my brand new blade, along with the top urethane tire, which I just installed last summer. I'm so hurt. Not physically, but mentally, and also heartbroken. I emailed Carter, not to ask for a replacement, but to try to find out if it was something I did wrong, or just the engineering of the way the rod rests on the rounded frame, which I personally feel is a design flaw. Of course, it could be that I applied too much tension, but I don't believe that to be the case, as I only put more tension on the blade until the cuts were satisfactory. Anyway after two emails to Carter, I have not received a response, not even an "it sucks to be you" response. What do you all think I did wrong? Jim Sent from my iPhone using Tapatalk Quote
Eric. Posted March 3, 2015 Report Posted March 3, 2015 Sorry I can't offer any advice to that specific problem as I have no experience with that product...but perhaps you don't really need it. Some blades are designed to be used at lower tensions. If your bandsaw doesn't create enough tension for a blade, I might try to fix the existing tensioning mechanism instead of messing with modifications. The saw should be capable of tensioning on its own. Again, I have no experience or knowledge about "ratchet rods," but my gut tells me that Carter invented a product for a problem that doesn't exist...if you can't tension sufficiently, you're using an inappropriate blade for your saw, or you need to fix your saw. IMO As an aside, Jim, you may want to change your handle to something - anything - that does not contain your email address...you're a spammer's paradise. Quote
dwacker Posted March 3, 2015 Report Posted March 3, 2015 And it took alot of tensioning to get the blade as tight as needed. This statement IMO says enough. 1/2 blades don't need a bunch of tension. The issue I see with devices like these is that its easy to over do it. If your tensioning tight enough to get the shimmy out of the blade with a little bandsaw then that is definitely the case. You can't do this with small wheeled saws the wheels are to small of diameter. Quote
jg9522 Posted March 3, 2015 Author Report Posted March 3, 2015 Thanks Eric. I didn't realize that my email address was my handle. I am getting crazy amounts of spam. Thanks again. Now to figure out how to change it. And there was not a problem with the tensioning on my bandsaw. All the Ratchet Rod is, is a regular rod, except it has Acme threads which are easier to turn, and it has a 3/8" socket head attached to the rod, with a ratcheting handle to make tensioning the blade easier and faster. Sent from my iPhone using Tapatalk Quote
jg9522 Posted March 3, 2015 Author Report Posted March 3, 2015 It was a 1/2" blade. The manual states that you can use a 1/2" blade. Sent from my iPhone using Tapatalk Quote
jg9522 Posted March 3, 2015 Author Report Posted March 3, 2015 Does anyone know how I can change my handle? I went in to edit my profile but couldn't figure out how to change it Sent from my iPhone using Tapatalk Quote
jg9522 Posted March 3, 2015 Author Report Posted March 3, 2015 Sent from my iPhone using Tapatalk Quote
dwacker Posted March 3, 2015 Report Posted March 3, 2015 Does anyone know how I can change my handle? I went in to edit my profile but couldn't figure out how to change it Sent from my iPhone using Tapatalk Go to your profile at the top of the page. Once there click edit profile. On the left click "display name". Change your name and your done. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.