Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Treating a Green Redwood Slab for a Mantel

Featured Replies

Okay, so this is probably similar to the Cedar Mantel thread...

I just picked up a fairly massive chuck of redwood that's basically 5x12 inches by 6 feet long that's going to be used as the top of a mantel. The problem is that it's still green and obviously I don't have 5-6 years to wait for it to fully dry before installing it. The client is very aware of this and does want the "rustic" look, so I'm not overly concerned about cracks and twists, but I would like to at least put some kind of at least basic finish on it to protect it and not have it look like a work in progress.

So the question is, how would you prep the wood? My guess it to seal the ends a bit with something like shellac to even out the evaporation, and then put a basic breathable finish on it. I am going to be attaching it so that it can freely float on the pedestals, and since he's a long-term local customer, I can go back in a few months/years and resurface and level it for him. The sawyer was also nice enough to cut it so there's no heartwood, etc. So it's fairly stable.

Any thoughts? So far I've been thinking either a simple sealing with shellac or polyurethane. I'm guessing both will breathe a bit, but I'm guessing I'll have more problems with the poly. Am I right in also guessing that since redwoods are coniferous, I could also have problems with pitch? Assuming that, I'm then concluding that the poly will end up being a cloudy mess.

Anyone have experience with redwood?

Wouldn't you just seal the ends with duct tape? :) (there's your Red Greene joke)

I've use a bit of redwood but here in California I mostly use redwood for outdoor (fence, planter boxes, decks, etc) and almost never finish it. So my first question is, why put a finish on it at all? If you client is looking for a rustic look on a mantel you don't get much more rustic than that.

I've noticed that redwood stays reasonably flat while drying but it will shrink a lot so plan for that. On my outside redwood furniture I don't notice much pitch and think you shouldn't have too much problems with pitch but I have had a couple boards with pitch dripping from it.

If you need a finish of some kind, I'd be most tempted to try a shellac with wax coat on top - something that might be easier to touch up in a year or two until the slab is fully dry. You might get away with just needing to re-wax it a couple of times. I'd avoid ploy if I knew there might be a fix up job in my future.

  • Author

The shellac/wax sounds about right. That was my thinking, too. Yeah, I'm not really looking for a heavy, solid finish. And maybe you're right: I might not need any finish at all. I guess it's just my natural reaction to "finish" anything I make, but I guess I should wait and see what the surface looks like once I plane and sand it. I use micromesh on some of my turnings, and they get glass-smooth without any kind of finish, so maybe I'll do something along those lines. The only thing I'd be concerned about is that I'm going to want to put some kind of sealer on the ends just to equalize the evaporation a bit, so it may or may not look odd with finish on part of it and not the rest. But again, if I polish those ends to a much higher grit, then it might not even be an issue.

Thanks for the tip on the shrinkage. I'm definitely setting it up so that it floats enough so that it can do its own thing. I haven't noticed any pitch yet either. Just wanted to make sure I wasn't missing something.

If pitch is going to be an issue I suspect you'll discover it in the sanding process.

I agree that most time I put a finish on things but thing why do we put a finish on? To change the color, add a glossy sheen, protect the wood... Guess I'm just the kind of guy that asks the question, "why?" a lot.

Redwood doesn't need much protection and on a rustic piece I wouldn't think you're going for a high gloss so your plan of seeing what it looks like after sanding before deciding sounds great to me.

  • 6 years later...

I am just starting out doing some simple signs and some routered signs for some of the local campgrounds. 

A good friend gave me some redwood slabs and I am trying to find a good way to protect the ends from further splitting. I also think there should be something put on this to protect it from. Deteriorating 

I am open to all suggestions. Thanks. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.