Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Stripping furniture

Featured Replies

I've used Citristrip Stripping Gel on a dresser, bureau, 13 draws, & wood around a mirror. The pieces are all wood, the top layer being a veneer. The finish, from the mid-1950's, I stripped was a high-gloss shellac or poly - whatever may have been used in the 1950's w/a whitish/light gray stain under the gloss. The Citristrip was left on from approx 20 min's up to, @ times on some pieces, approx 1+ hr's; no more than 2-3 hr's max; most pieces in the 20 min-1 hr range. Many of the pieces now have lighter spotting on the bare wood, areas where I had to use a 2nd application of Citristrip because these areas didn't completely strip the 1st time around. I cleaned these areas wiping w/paint thinner & then wiped w/bleach. As the spotting did not go away, I applied a 3rd coat of Citristrip on the entire areas to try to get the pieces uniform. The 3rd coat did not make the pieces uniform, they are still spotted. I've cleaned the pieces w/paint thinner & even tried bleach on the entire pieces again; all to no avail. I was hoping to stain the furniture but now can't w/the spotting. I also tried to lightly sand, w/220 grit, but the blotchy/spotty wood still shows, though it is slightly lessened. I can send photos if you can tell me how to attach them. Do you have any suggestion what to try to eliminate the spotting & make the pieces uniform for staining?

Edited by haroy

I have never seen a stripper that takes stain off wood and cleans it down to almost milled quality. It takes sanding and lots of it sometimes. Paint thinner takes off paint, Lacquer thinner takes off lacquer, and that being said don't expect it to just POOF come off either. Bleach will not do much if anything for you. Mixing up all those chemicals is probably not helping you. Let the pieces air out and dry then take it step by step that way you are not doing a chemistry experiment on your project. If you take your thinner and wipe it on with a rag, cover one piece and stand back and look to see if you can see the blotches. If not than you don't have anything to worry about. Those spots can sometimes be the wood sort of getting burnished from working it so much. I dont know what kind of wood you are working on but Im guessing its oak and oak has some very open grain. Naturally it is very blotchy so that might be adding to your concerns.

Now if you look at the bottom of the page where you add your post you will see a button that says, "Use Full Editor" Click on that and that will bring you to the proper place so you can upload some photos of what you are working on. It is the same uploader as all the other sites but keep in mind that picture size is very limited so you may need to shrink them down first. I look forward to seeing exactly what you have going on and also to getting you past the hurdle. I hope others can chime in here because what I have talked about may not even be what your problem is. Pictures are great to help others help you.

  • Author

Thanks Scottie. I have 6 pictures & I'll probably have to send ea 1 separately because they're ea approx 2.75 mb. Here goes ...

  • Author

I don't think pictures are attaching because they're too large. Do you know how to make the files smaller?

I hope you receive this picture; I tried to re-save/resize.

I don't think pictures are attaching because they're too large. Do you know how to make the files smaller?

I use a photo editing software to just chop them down. Or use the lowest resolution on your camera and take new ones and try that.

  • Author

Trying again ... success I think. Thanks for your patience.

post-5016-0-45200500-1308358523_thumb.jp

  • Author

Picture #2; side of bureau; see lighter area across & closer to bottom

post-5016-0-24667300-1308358761_thumb.jp

  • Author

Picture #3. I think these 3 pictures (2 sent previously) are good examples. If you need to see more, please let me know. Thanks again.

post-5016-0-84968900-1308358912_thumb.jp

Trying again ... success I think. Thanks for your patience.

Did you wipe your thinner or mineral spirits on it and see what it looked like? If not try that. If the spots are still there after you covered it with whatever you are using than sand on it some more. Don't go to crazy and start changing board thickness to much but see if it helps. If all that fails you can do a test stain and see how it takes. That is if you are going to stain it again. Try it real light (time, pressure) and see if the stain takes evenly over the lighter blotches compared to the rest of the board. I guess that is all I can say for now. Hopefully what I mentioned will help you, or worse case someone else will come through with words of wisdom

edit: The pictures were added after I posted this. It looks like the bleach did its job on only some parts (the blotches). Not sure how to recover from that but like I said, try the above it might work out.

  • Author

Did you wipe your thinner or mineral spirits on it and see what it looked like? If not try that. If the spots are still there after you covered it with whatever you are using than sand on it some more. Don't go to crazy and start changing board thickness to much but see if it helps. If all that fails you can do a test stain and see how it takes. That is if you are going to stain it again. Try it real light (time, pressure) and see if the stain takes evenly over the lighter blotches compared to the rest of the board. I guess that is all I can say for now. Hopefully what I mentioned will help you, or worse case someone else will come through with words of wisdom

edit: The pictures were added after I posted this. It looks like the bleach did its job on only some parts (the blotches). Not sure how to recover from that but like I said, try the above it might work out.

  • Author

Hi Scottie,

Yes, I did wipe the wood w/paint thinner again today, after it drying for 2 wk's (wasn't really letting it dry that long-it was dry long before, but I just don't know what to do w/finishing now that I've created this spotting), - the spots do show even when the entire surface is wiped-down wet w/the paint thinner. The spotting isn't from the bleach; it happened after I worked the 2nd coat of Citristrip Stripping Gel into the wood to try to remove the rest of the paint/stain (whatever was used to color the wood in the 1950's). It's those areas that I worked the 2nd coat in, going back & forth w/the paint brush, that created the spotting.

I did sand to try to get the spotting out or lessened but the spotting is still quite evident. I'm afraid to sand much further as it is a thin veneer wood & I don't want to wear through it. My only thought, similar to what you mention, is to try to lightly stain the lighter spotted areas then try to stain the entire surface after those lighter spotted areas are dry ... & hope that the staining looks even. I'm not thinking this technique is going to be completely successful but if I want to stain, I don't know if I have any other options. I hate to paint it after spending all that time to strip it to stain.

The only other thing I can think of to try, & already tried it w/applying a 3rd coat of the Citristrip, is to apply a 4th coat, working it briskly w/the paint brush into the wood, & leaving it for some time, to see if this last try will result in a more even finish to the wood. Because my 3rd try was not successful, I once again do not hold out much hope.

Lots of work for pieces that are not $/valuable but the pieces were my parents 1st bedrm set they had when they married, the pieces needed to be refinished, I have the furniture & have need to use it, have worked hard on it, ... & I'd really hoped it would look great when refinished.

I'm open to any more suggestions if you think of any ... or if anyone else would like to comment. Thank you again.

Crappy! I would think the staining approach might work but you would have to have some luck on your side too. Its like the stripper reacted with wood or glue and created more problems than good. You can try sealing it somewhat and then using gell stain to "paint" on the stain and look but with that you will loose some wood grain because it will be thicker in areas, and thinner in the others. I guess at this point anything is better than turning it into fire wood. Let us know if you come up with a remedy!

  • 5 months later...

A water-based remover is as effective and less dangerous but is slower , a matter of a few hours. It raises the grain which means you have to sand the surfaces after stripping.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.