Recommended Posts

Posted

I have read and (hopefully) applied the information from the other "Plane Chatter" from June 2011 on this forum, but I am still screwing something up bad. Here's my issue:

Just got a Woodriver Jack Plane. Sharpened it as best I could (first time), flattened the sole as much as possible and checked the frog and chip breaker for flatness and made sure they lined up square and flush. I used the plane on some cheap Home Depot "whitewood" and it cut like a champ. Really fun to work with... I know that stuff is soft and cheap, but I was thinking I was doing something right. But, I then tried it on some Red Oak that needed flattening and the plane skipped around and would constantly get caught up in the wood and make straight gouges or something to that effect. I couldn't get across the board with one pass (not even a few inches!) without skipping and gouging and getting stuck. I am trying to take super light cuts at a skew (and really started man-handling the strokes) and have managed to still get the same problems, but to a very lighter extent. I'm still only making little dust type shavings and can only move the plane an inch or two without it skipping, gouging and getting stuck...

I've re-sharpened it again and I am pushing with all the muscle I got and I have gotten 3-4 good shavings over a 6 inch span, but that's it... I switched up the direction in case I was messing something up with the grain direction... not really helping.

Any help would greatly appreciated.

PS I've read tons of books on this matter and have watched LOTS of youtube videos to no avail!!! I'm a hack!!

Thanks.

Posted

Your iron isn't sharp enough, what are you using to hone?

4000/8000 grit waterstone with honing guide from Woodcraft. I follow the youtube videos I've seen and it cut my thumb nail after sharpening. I definitely know my sharpening skills leave much to be desired. I suppose I can start there and try again.

My father-in-law, who woodworks from time to time, came over for dinner tonight and said to make sure that the board itself is tight on the workbench (there was a ever so slight wobble when I had it clamped - probably from forcing the plane!)and to muscle through it. I'm not so sure that I have to power through the wood like Hulk to get it to plane. Seems a little too dangerous...

Thanks.

Posted

Your stones should do the trick, are you honing until you feel the burr along the edge, then knocking it off?

If your iron is sharp I'd suspect you're taking too big a bite or working against the grain.

You shouldn't need to clamp your stock, in fact you should avoid it, as the clamps exert their own stresses and can flex the stock. An end stop, and some shavings under the high corners to keep it from rocking, are all you need.

Skewing the plane wll make it easier to push but the risk of tearout grows the more you skew it, as you are dropping the cutting angle by doing that.

Posted

Try setting your plane so that the blade isn't protruding at all, then slowly advance it little by litte, trying to plane after each adjustment. When set for the finest cut, your plane should take a shaving even against the grain (though the resulting surface will be rough). If your plane doesn't pass the test, check your sharpening. Oh, also check that none of the adjustment screws are loose.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 40 Guests (See full list)

  • Forum Statistics

    32k
    Total Topics
    437.5k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Lenny2
    Newest Member
    Lenny2
    Joined