luthier_ted Posted November 3 Report Posted November 3 Hi all, I recently bought a used Laguna 16-32 drum sander in excellent condition. I had the machine installed in the workshop and ready to test so for the first test I just checked the condition of the paper, cleaned it and sanded a small block. Looked ok on initial inspection but I soon realised that the shop vac would not be able to cope with the amount of dust this thing kicked out. I put the sander to one side till I figured out how to improve dust extraction. A while later I decided to check the calibration of the machine. On the outfeed side any stock passed to the drum here would hit the roller and the drum housing would shudder. I checked a few more things and found the drum was not parallel to the table, the belt was sliding off to one side and any piece sanded had leading and trailing edge snipe. I managed to get the drum level by following the procedure in the OM but the snipe was a much more involved process. Laguna state that the rollers are set at 2-3 turns of the drum when the drum is resting on the table. Problem is that on my machine this makes the shudder worse to the point that the stock will not pass under the roller without significant assistance from my hand. I have played around with the roller tension screws, replaced these and the springs, took the brackets apart to clean and lubricate, set the roller height at one turn only all to no avail. I still have snipe at both ends and there is still a slight judder in the drum house on the outboard side when contact with the roller is made. I've also tried reversing the rollers swapping the front for the back. Nothing I have done has improved this. On the motor side, there is no issue and I can get to within 0.1mm variance over a 200mm long by 40mm wide stock. But the minute I try a wider piece that extends across the table to the outboard side all measurements go to pot. I am very disheartened by this as I have spend 3 days from 8am to 6pm trying various different settings to iron out these flaws. I cannot see any damage to the machine, the drum and table are perfectly flat so I am at a loss on what to try next. If by any chance there is anyone who has successfully dialled in this machine please could you share some tips, it would be gratefully received. 2 Quote
Popular Post gee-dub Posted November 3 Popular Post Report Posted November 3 This sort of thing can happen when we start adjusting things without knowing what exactly is out of adjustment. Jointers are notorious for this. You end up with a cascading effect that is quite a bit like chasing your tail. I would return the machine to factory spec and start again. Have you had drum sanders in the past? Many folks expect them to takeoff way more material per pass than they are designed for. My Supermax (now owned by Laguna) raises or lowers the drum 1/16" per rotation. I tend to move the mechanism 1/8 of a rotation at a time. For example, from the owner's manual for the 19-38: Setting Drum Depth of Cut: Determining the depth of cut is the most IMPORTANT set-up procedure before operating a drum sander. It may take some experimentation to determine the proper depth of cut, given the variables of abrasive grit, type of wood, and conveyor feed rate. Practicing on scrap before sanding a project can be beneficial. A good rule-of-thumb when sanding is to place the workpiece under the drum and lower the sanding head until the workpiece contacts the drum but the drum can still be rotated by hand. When making successive passes, lower the sanding head no more than the thickness of the grit abrasive, I.e. 1/8-1/16 of a turn for 80 grit and less for finer grits. Note: one revolution of the height adjustment handle moves the sanding head 1/16”. Unless I am mistaken the pressure rollers keep the material in contact with the feed belt. The feed belt moves the material under the drum where it gets sanded. The fact that you are getting snipe can be from a couple of things. No infeed or outfeed tables to control the material during the feed is one thing. The drum being lower than the pressure rollers can be another. Here's a shot of mine: You can see that the pressure rollers fully contact he material before the drum is even close. Additional lowering of the carriage assembly puts more pressure on the material assuring a reliable feed. The relationship between the drum and the table control the result. I know this is a lot of blathering on and I am having to make some assumptions. I still recommend getting the machine back to factory default and proceeding from there. If you don't have a method for measuring the table to roller / drum dimensions you can make something from a 1-2-3 block and a cheap dial indicator. We are not after machinist level analysis here but plus or minus a few thou would be good. When I am going to setup a machine I do just about what you have done. I set aside the day knowing it may take 30 minutes or 7 hours regardless of the machine. I know I am beating a dead horse here but I again feel that you need to get back to factory default before you start moving anything. 4 Quote
Biotec Posted November 4 Report Posted November 4 @luthier_ted Maybe in this video it will help you it's nine years old but he describes a lot of the same things that you have described with yours on how to adjust and bring it back into alignment. https://youtu.be/vd2lmO-7zfE Here's another one from the manufacturer for about 7 years ago https://youtu.be/_fDUKDB-A1Y?si=49AAHRDmwFmMRLwl Here's another presenter with a new machine talking about how to get the belt to track and consistency https://youtu.be/RigBl_1kCNA?si=_OnuUuY20K-85GG8 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.