Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

A new to me band saw.

Featured Replies

I just bought a 1930's era Boice Snowflake band saw. It is in decent shape but will need a bit of tlc to really bring it back to life. I have a real affection for old iron like this. The New stuff may be nice, but will it still be around in 80-100 years?

I have attached a picture of the saw so you all can see.

I paid $200 for the saw. It has a new General Electric 3/4 hp motor on it and several spare blades.

Here is one similar to mine:

http://vintagemachinery.org/photoindex/detail.aspx?id=4659

http://vintagemachinery.org/photoindex/detail.aspx?id=13067

http://vintagemachinery.org/photoindex/detail.aspx?id=1665

post-5569-0-46897700-1322946583_thumb.jp

Nice find. I'm sure you'll enjoy restoring it to it's intended purpose.

  • Author

I got it running today. It was completely out of adjustment and most of the adjusters are junk. I tore apart the upper guide block and started rebuilding it by cleaning it up, filing the burrs off the steel pieces and generally giving it a once over. I had to drill out the 21/64" nylon guides and will need to replace them as well as the thrust bearing as the bearing is froze up solid. I don't think either should be that hard to find.

This bandsaw was offered in two configurations: 1) single pulley system for woodworking and 2) multi-step pulley system for metal cutting.

Given the amount of greasy goop that has accumulated on the saw, I would say that it lived most of it's life cutting metal.

More later.

very nice find! I'm partial to old arn also. I frequent the owwm.org forum most days too.

  • Author

Today, I went over to Allied Machine here in Olympia and bought a direct replacement bearing for the blade guides. Then I drove up to Tacoma to pick up some UHMW plastic to make the guides from. The saw needs 21/64" round stock for the guides. I bought 1/2" stock and will simply turn it down on the lathe.

The final part of my trip today was to run into Seattle to Dusty Strings and pick up some strings and hardware for the harp I will be building soon. I hope to start on it this week.

  • Author

Well, I am happy to say that my idea of using uhmw and turning it down to the size I needed actually worked. I don't know how long it will hold up, but I have enough to make about 30 more of those little guide dohickeys.

  • 4 weeks later...
  • Author

ok,

So I got the saw all set up. The blade is tracking well and the guides are holding up. This saw cuts through stuff pretty well considering the size.

I have no trouble cutting shapes in hardwood. I have tried to set the saw up for resawing however and it is not doing that job well at all.

The table is square to the blade. The blade is sharp and tensioned properly. I have done the "cut a straight line" test and set up the fence that I built so the cut will run true.

When cutting up to about one and a half inches, it tracks pretty well. However, anything over that and the blade wants to pull away from the fence to the right.

I have not dressed the back edge of the blade yet, so that is my next step. This is an operation I have never had to do before and I need to be able to cut strips of wood about 1.5mm thick reliably as the wood is much more expensive than what is normally bought in a hardwood store.

Also, I will be resawing Spruce and Mahogany up to 6" thick to about a 1/4" width for soundboards for harps.

Is there anything I have missed or do I simply have the wrong tool for the job?

Thanks,

VM

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.