Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Epiphanes

Featured Replies

Marc,

I read your endorsement of epiphanes as your outdoor varnish of choice, and i also watched your video about cutting board finishing.

Am i nuts to want to apply the same principle (saturating the wood with progressively less thinned coats of varnish but not building a film) with epiphanes on a cedar deck?

The deck has not been built yet, so I will have access to all 6 faces for finishing. Is sealing it all the way around a bad idea?

Finally any other wood you would recommend for decking that is still reasonably priced (cedar +\- 50%)?

Thanks,

Max

Hey Max. My advice quickly goes south when talking about large scale and construction projects. Most of the materials I use are specifically for small scale projects, most of which wouldn't be all that practical on a larger scale. That even includes many of the wood species I work with. And any deck I have ever been involved with was made with good old pressure treated lumber, lol. But to answer your question about the finish, that's a very interesting idea. The problem though is that it won't offer much protection. It certainly could seal the wood to some extent but might not offer enough lasting protecting for something that lives outside in the elements. Also, Epifanes is quite expensive so you're going to go through quite a bit of it. That said, if you do put on a decent film thickness, the deck would certainly be well-protected. And sealing on all sides is certainly better in the long run, but once again, is it practical? Hard to say. I'll throw this into the Finishing forum and hopefully someone with a lot more decking experience can chime in.

I have built many of decks and I have finished them bother before hand as well as with each cut being finished before installation of the board (very time consuming) and just sealing the tops. All of the decks are holding up just fine. I have not seen any difference in the decks that are finished all around from the ones that are only sealed on the top. Either way you will be refinishing the top in a couple of years and it's a lot easier and cheaper to just seal the top.

If you want something you really don't have to deal with then go with ipe or kumeru(sp?) basically the same wood but both are awesome and are rot resistant and bug resistant. That coupled with a nice PT frame you will have a deck that will most likely out last you.

Personally I don't think that a 1-part varnish (like Epifanes, Captains, etc) would be the right choice for a decking finish. Could it be done? Sure, but it wouldn't give the wear characteristics / protection that a deck needs. Varnish is actually quite soft and will scratch very easily (foot traffic, moving the grill, pets, sweeping, etc). I typically don't recommend a varnish finish for anything that would be a "wear" surface (seats, floors, etc) just for this reason.. Also, being a high gloss finish that's something that's typically not used for a floor as it reflects too much light and is hard on the eyes :-O

Once you start looking at 2-part "varnishes" (which aren't what I consider a varnish at all but a 2-part polyurethane) they are much harder and well designed for wear surfaces, but cost a fortune!! I think a good 'ol decking finish (maybe a sikkens product) would be the best route and if you wanted to use a varnish on some "highlight areas" that would probably look pretty sharp!

Hope this helps :-)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.