Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Woodpeckers Sidewinder router lift install

Featured Replies

well i dialed in my new table saw so now its on to installing my new sidewinder. I glued up a double thickness piece of 3/4" ply and mounted it like a 3rd extension wing on the table saw. I cut and routed the hole for the plate. The scrap piece that came from the center i used to mount the great switch i got from amazon.post-577-0-31759400-1338073003_thumb.jpg

I used 1/2" aluminum angle to line the ledge the lift sits on so the level set screws wouldnt dig into the wood and lose accuracy. post-577-0-01984100-1338073135_thumb.jpg

Then i built a box surround for dust collection and noise control. There is a 6" blast gate on the bottom so when i am using just the table saw it wont detract from the suction from the saw. i bored 2 holes, 1 for the plug and 1 for the actual sidewinder arm to poke out through. post-577-0-24236000-1338073265_thumb.jpg

I still need to build an aux fence for dust collection and regular tasks. so far it works well and am very happy with it. Does anyone see anything that could be different or changed. i didnt have a 4" blast gate kickin around for the saw side of the dust collection but was very pleased with suction through the box without a gate.

You are really going to enjoy that setup, Jason. As you look for some sort of top dust collection, you might want to give a thought to how you could possibly have one unit serve both the TS and router.

  • Author

Yeah thats what i was thinking. I was going to hold it on with fence clamps. Something like on my old bosch ra1171 table.

Another question i have is should i install a miter track or is it useless. I never used ut on my old one so im unsure.

I'm sure others will pipe in, but I have one that is seldom used, but when I do, am very glad I have that option. Shop Fox even manufactures a jig designed for use in such a slot.

  • Author

so i have been reading about aux fences. i may just want to make a dedicated router fence with magnets to hold it in place. you know just in case i need to use the table saw fence too. how do the magnets work, are they strong enough for this situation? if i have to i will go back to my original thoughts and use a aux clamp on fence.

I think you will find the switchable magnets quite suitable in terms of holding power, so long as you use two (if I recall, about 70lbs apiece). The challenge is how you project the fence into the bit. You could also consider routing out parallel channels and using t-tracks for a fence mount. You really want the fence to be able to run up to (and beyond) the router centerpoint. Incra, Rockler, MLCS and others have different tracks. I'd also consider getting a multi-track so you can use it for both runners and hold-downs.

Take a look at the architecture of the Incra fences. You can see that they are able to use a central mounting point and then telescoping the fence along the axis. That may generate some ideas.

Anytime you are fabricating a custom (semi et al) shop fixture, it also pays to look beyond the primary function to see if there are also other uses for the space. You may also want to use the surface for manual router operations and by having set registration points (parallel tracks, hold downs, dog holes, etc), you will get more mileage out of your efforts.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.