JimReed Posted August 14, 2012 Report Share Posted August 14, 2012 I was able to get unfinished T&G white oak flooring REALLY cheap so I decided to go all out and install this over 1 1/2 insulation and plywood. Despite the fact that the flooring was "seconds" it looks great. I am looking for recommendations for finishing this flooring. My thought was to forego any sanding and just apply some type of protective sealer (oil, poly?) to permit easy cleanup and to prevent any staining or glue sticking. I am not trying to achieve a "gym floor" highly polished sheen. In fact, I like the look of the unfinished floor but I know that look won't last long once I start tracking in water and mud. Does anyone have any recommendations for a product that is easy to apply and fits the bill? Can I get away without sanding or do you think I need to sand first? Thanks, Jim Quote Link to comment Share on other sites More sharing options...
Hybrid-woodworker Posted August 15, 2012 Report Share Posted August 15, 2012 Hi Jim, If it was my shop, I would not sand, I would want the roughness for traction. Also I heard a tip recently to use a water based poly. It also raises the grain adding texture. The water based poly can be had in a real clear which should showcase the look of your floor. BRuce Quote Link to comment Share on other sites More sharing options...
JimReed Posted August 15, 2012 Author Report Share Posted August 15, 2012 I would greatly prefer to NOT sand but I wasn't certain how not sanding might effect the finish. I read some good reviews of Bona Traffic, a two part water based finish, last night. Anyone have any good/bad experience with this product? Quote Link to comment Share on other sites More sharing options...
tim0625 Posted August 21, 2012 Report Share Posted August 21, 2012 Kind of a tradeoff...slick sweeps nice, rougher=mo' traction. But...since you don't care about the shop being a showcase (attaboy) why put anything at all on it? Natural wood just gets a little dirty looking over time. An occasional glue drip isn't that big of a deal....if you're worried about traction, leave it bare. If not, a sand n' seal or poly will give a coating. Poly with some sand will coat and give gripshun. Quote Link to comment Share on other sites More sharing options...
suiciedchild Posted August 30, 2012 Report Share Posted August 30, 2012 If your going to finish it I would sand it, I would add an additional step though, there is a wood filler that you use a trowel or a rubber gum float to apply , much like a "pore filling " on a piece of furniture, it will fill in all the little gaps between the boards where stuff can get trapped, being that it is "seconds" the boards aren't going to be perfect, then sand after that is applied. The Bona Traffic is a great water bourne finish, very commercial and durable. You could do like you normally would do with raising the grain, and go around with a water spritz bottle after the filler and light sanding, then apply the Bona. I wouldn't finish it without a sanding, I think you may regret the way it looks afterwards, how many of us have rushed to apply finish to a project and then stripped it off only to do it again. Quote Link to comment Share on other sites More sharing options...
suiciedchild Posted August 30, 2012 Report Share Posted August 30, 2012 P.s if you want that slight texture you can skip the sanding in between coats. Never seen anyone throw sand into it, not sure how I would like the way that looked. Quote Link to comment Share on other sites More sharing options...
Grain Guy Posted August 30, 2012 Report Share Posted August 30, 2012 I would not leave it raw. You will work dirt and grime deep into the floor. If you ever wanted to refinish for resale, it would take a good amount of work to sand that junk out. Rock on with a coat of something. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.