ChetlovesMer Posted November 29, 2012 Report Posted November 29, 2012 Okay, I just got my new Clearvue Cyclone set up and a plan for where I want to run my pipes, tubes, ducts, what ever you like to call them. I'm using about 90% 6-inch PVC. This is per Clearvue recommendations. Anyhoo, I'm just curious for anyone else who's used PVC, how did you hang it from the ceiling? From the walls? I have a couple of ideas, but I figured with all the clever people on this forum it was pretty likely somebody has something even better. If it makes a difference, I don't plan to move it very often. The general layout of my shop hasn't changed much in 2 years and I don't suspect it will in the next 2 or more years. Quote
robjeffking Posted November 29, 2012 Report Posted November 29, 2012 How High are your ceilings? Quote
ChetlovesMer Posted November 29, 2012 Author Report Posted November 29, 2012 Good question: They are supposed to be 14 feet. But in reality they are a few inches shorter than that. Quote
robjeffking Posted November 29, 2012 Report Posted November 29, 2012 My ceilings are 16' I used a stainless steel roll of utility/bailing wire to suspend then runs down the center of my shop and plumbers tape against the walls. This wire can be temporary or permenant it will allow you to fit your pipes change heights,direction after your satisfied with your layout then you can use a more ridgid solution. In my case I went back and added more wire pulling the pipe in both directions at a v angle that elimnates side to side motion. Quote
Eric. Posted November 29, 2012 Report Posted November 29, 2012 For places where it's secured directly to the wall or ceiling, I just used that galvanized strapping...I believe it was made for exactly this purpose. It's in the isle with all the other pipe supplies at BigBox Depot. For places where I needed it to hang below the ceiling, I used a few of those plastic hangers with the strap at the end...kind of like a giant zip tie on a stick. Same isle. They also make those hangers in galvanized but I don't remember seeing any 6"...my system is all 4". I'm sure they have them at places like Penn. And in a few places you just have to get creative. Quote
robjeffking Posted November 29, 2012 Report Posted November 29, 2012 We call the strapping with the holes in the center plumbers tape. The steel wire will get you started and hold up your pipes while your getting your system laid out in my case I needed a very long hanger and the wire was my best solution I used the same wire inside the pipes to ground the system from static charge. I never glued any of the fittings tape and screws on the joints. Quote
TimV Posted November 30, 2012 Report Posted November 30, 2012 My 6" PVC runs parallel with my floor joists (I'm in a basement shop). I simply have blocking screwed between the joists holding it up into the joist cavity. Then, I have the y's down at an angle reducing to 4" for each machine line. I use the aluminum hvac tape between all the joints. Quote
ChetlovesMer Posted November 30, 2012 Author Report Posted November 30, 2012 Right now I have a roll of plummer's tape, a huge bag of zip-ties, two rolls of aluminum hvac tape, and a sketch of where I want everything run. Hopefully something it will all happen this weekend. Having written that, I should also note I'm responsible for putting up the Christmas lights this weekend as well, so we'll see. Quote
robjeffking Posted November 30, 2012 Report Posted November 30, 2012 I think Ill run some christmas lights around my dust collector ducts Quote
Alan Bienlein Posted December 1, 2012 Report Posted December 1, 2012 I made wooden brackets for my duct work. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.