Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Weak Figured Maple?

Featured Replies

Hi everybody,

I am building some speaker cabinets and I am using tiger maple to make the side panels. I am having trouble getting the figure to show up, and not just in the finishing part - I mean it hardly shows up at all! I know the stripes are there - I can see them in the right light, and I can see them when I wet the wood with water and I can see them on the end grain and most of them run completely through the wood. I initally sanded the wood with 60-grit to get the blade marks and other dents, scrapes, etc out. When I did this, the tiger stripes almost seemed to disappear. I then sanded to 80-grit and the seemed to show up just a tad more. I tried using water based general finishes stain, transtint dye with both water and alcohol and while it brings out the stripes a little more, it is never like the youtube videos or other projects online look. The stripes are very weak. If I sand the stain off, it has hardly penetrated the stripes.

So, am I doing something wrong, missing a step, or do I have just some very weak tiger stripes?

Thanks for any insight you can provide!

I'd sand tiger maple to at least 220, maybe even 320 before dyeing. Ditch the pigment stain altogether. Pigment stains are almost useless on this stuff, as there isn't much for pores to hold the pigment, and stopping at too rough of a grit will cloud the figure.

You can even polish maple out to 800-1000 after dyeing, it'll get super smooth and beautiful.

Practice on offcuts...

  • Author

Really, you would sand out to 220 or 320 before dyeing? Almost every video I watched shows it working great starting at 80grit...

I didn't like the pigment stain either - it was the first one I tried. I am working on scrape pieces, but I have used them all up now. I don't want to buy more cause there is a chance it won't be like the maple I am using, which is what I am having trouble with. I've seen other boards with a stronger figure, but I can't afford to buy more and do everything all over again.

Anyway, since my stain doesn't penetrate deeply, its easy enough to sand off and start over.

Barry's right...keep sanding. 80 grit isn't finish ready on any wood, especially maple. 180 bare minimum. And after you dye, finish with oil based instead of water based. That should help bring out more of the chatoyance in the figure.

I sand to 150 then dye the wood, apply a heavy enough coat so the dye will soak down into the curl (tiger stripes which is end-grain). Once the dye is dry. Machine sand the dye off. This leaves the dye deep in the curl while machine sanding removes the dye from the flat grain. Repeat up to 3 times depending how dark you want the curl. Then I will take some general finishes seal a cell and apply a thin coat to drive the dye deep into the wood. Then stain to tone the flat-grain.

Using a weak solution of black dye is good. Then go over that with a brownish type dye.... gives a nice show. Not sure what colors your going for....but the key is to practice on scraps or the inside of the speaker cabinets.

Figured wood is tricky. After finishing, sometimes the figure just flip flops and disappears. You look at it from one side of the room you see it. Go to the other side of the room it disappears.

Also the key to building with figured wood. Is to orient your wood with the bark side out. Meaning pay attention to the growth rings in the wood. Bark side out, displays figure the best. That’s why folks who build in figure wood will get some dye on the wood to see how the figure is going to appear prior to construction.

Try visiting some of the guitar building sites...very good info on finishing tiger maple using mostly dyes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.