Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

correct breaker size for powermatic planer

Featured Replies

So I bought a powermatic planer and in the manual it says to use a minimum 40A breaker...does this mean that I could use a 50A breaker if I wanted to? I wasn't sure if the 15HH had some sort of internal breaker or not. It also says a minimum of 20A for the 882HH jointer I got....

Although after reading the manual again maybe the breaker size is exact and they are really refering to the guage of wire that is used?

  • Author

I would prefer to do what the manufacturer recommends....after rereading the manual I think that they are referring to the guage of wire to use with the breaker when they say "minimum" so basically for 40A use a minimum of 8 guage wire.

I was questioning hhh's advice about useing a bigger breaker than the tool spec's call for. So I talked to my friend Scott who is a qualified electrician, and he said it's OK to go with a higher amp breaker than tool spec's if your useing the proper gauge wire for the amp breaker being used. As he explained it the breakers job is to keep the house wireing from overheating and causeing a fire, the tool itself regulates it's own overheating issues with an internal beaker, useing a smaller amp breaker than the tool spec's is where the issues would arise the higher amp draw from the tool would cause the tool, and the circuit to overheat which would cause the breaker to kick, the tools internal breaker to kick, or both. The only downside to upping the breakers amps would be the costs of the higher gauge wire, and the cost of the breaker. Hope this helps if you have questions go to an electrical parts house and ask your questions they useually are quite helpful, I'm not talking about HD, or Lowes in my area the parts house I go to is Platt Electrical I'm not sure if they nation wide or not, but I'm sure there is shop where the elctrical contractors do buissness.

The way I understand it a circuit that would be under amp-ed for a tool, that would cause overheating, not the other way around. I'm just going by what Kenny's original post question was which is can he increase the breaker size, and from the conversation I had with my buddy it isn't a problem if he also increases the size of the wire, the operating voltage is still 220v the breaker senses heat build up in the circuit, because that is the danger a under rated circuit would cause the motor to work harder than it needed which would cause the circuit, and the motor to heat up, and kick the breaker. I agee with you not to put his shop in any danger thats why I was telling him to investigate, and to take advice that he gets off this forum at face value, if the advice is about woodworking it pretty subjective, but if it's about electrical it's pretty cut, and dried. I only disagree with this one point I totally agree with useing caution.

  • Author

I went with the 40A breaker and 8 guage wire....if you use a smaller guage wire you can have heat issues which can lead to a fire....which is bad....my opinion is do it right the first time and don't cut corners....trying to save money when doing electrical stuff is generally not a good idea....

Not following the manufacturers recomendations usually voids the warrenty. Regardless if I'm buying new or used I'd rather spend a couple extra bucks on some wire and a breaker, sure beats replacing the unit and dealing with the down time. In most cases it takes less time to do it right the first time, cutting corners has always come back to bite me in one way or another.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.