Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Shop lighting...opinions and inputs

Featured Replies

I am looking for opinions on upgrading the lighting in my shop.

Some background - We purchased this house about 18 months ago, and one of the things that sealed the deal was the fact that there is a 20' x 24' detached garage/shop. Part of that space is a covered 'back porch' so the actual shop space is 20 x 20 ( realistically 19.5 x 19.5 interior). The previous owner used it to maintain a classic Mustang, and it was built/designed with that purpose in mind. The front has a single roll-up door and a normal entry door to the right of the roll-up. There is a second regular door that is directly opposite the entry door that opens onto the porch. There is a row of base cabinets to your right as you enter that covers ~16' with a small sink. The back wall has an ~ 40" high shelf that starts at the door and continues left to the corner. There are windows on 3 walls that let in a fair amount of light, the garage door has windows along the top panel, and the front door is half glass. However there is also a lot of tree cover, so light entry can vary.

Electric - Fed into a sub-panel with 4 circuits currently. 2 cover the wall outlets, 1 covers the lighting and ceiling outlets (i think), the 4th is for a dedicated outlet (currently used for the A/C). There is also 1 220 outlet right below the sub, not sure which circuit it is on.

Lighting - The only lighting when we moved in was a single 4' 2-bulb fluorescent fixture that was over the counter on the right side. That's it. I installed an 8' 2-bulb fluorescent that runs approximately down the middle of the main 'work area' that was being used to light the attic (lord knows why you need that much light in a place you never go). When the garage door is up it covers about 2' of the fixture.

The shop layout is still very much a work in progress. I typically put my table saw in front of the garage door (about 2' inside) so that my the outfeed goes towards the center of the shop. I typically have my main work area (a half sheet of 3/4 ply on sawhorses) immediately behind that as an outfeed. My router table is usually to the right of the TS, butted against the extension on that side. My bench is along the left wall and my scroll saw and miter saw are along the back wall against the shelf. My lunchbox planner gets stashed wherever there is space (right now its on the end of my bench) and my drill press will sit either on the cabinets or the back shelf when I get it assembled. I still need to develop a lumber storage system as it is wasting space, and I would like to take down the shelf along the back wall to make that more useful and put tools against that back wall. Up to this point I have kept the corridor between the two standard doors clear. I also added a shelving unit at the end of the base cabinets, so that wall is now completely covered.

I have been looking at 2, 4 and 6 bulb 4' fixtures and trying to figure out the best option both from a cost perspective and proper lighting. I read thru the omnibus Shop Lighting thread and I downloaded a copy of Visual and plugged in the fixtures i was looking at:

http://www.homedepot.com/Lighting-Fans-Indoor-Lighting-Industrial-Shop-Lighting/h_d1/N-5yc1vZbvnq/R-202193185/h_d2/ProductDisplay?catalogId=10053&langId=-1&storeId=10051#.UN-k1qzNl8E

http://www.homedepot.com/Lighting-Fans-Indoor-Lighting-Industrial-Shop-Lighting/h_d1/N-5yc1vZbvnq/R-202968125/h_d2/ProductDisplay?catalogId=10053&langId=-1&storeId=10051#.UN-k1azNl8E

http://www.homedepot.com/Lighting-Fans-Indoor-Lighting-Industrial-Shop-Lighting-Strip-Fluorescents/h_d1/N-5yc1vZbvm3/R-202052422/h_d2/ProductDisplay?catalogId=10053&langId=-1&storeId=10051#specifications

I wasn't able to find an exact match for the model number for the 2 and 4-bulb fixtures in the files, so i made a best guess by looking at the Lithonia website. I set the work height at 3' and a mounting height of 7.8'. Walls and ceiling are white, floor is concrete stained gray. Here is what i got from Visual:

4x 6-bulb fixtures = 112fc (column spacing of 8' and row spacing of 10')

4x 4-bulb fixtures = 79fc (column spacing of 8' and row spacing of 10')

6x 4-bulb fixtures = 119fc (column spacing of 8' and row spacing of 6')

9x 2-bulb fixtures = 77fc (column spacing of 4' and row spacing of 6')

Not knowing exactly where all the tools will end up and what my final work flow will be, I am hoping to get a lighting plan together that will give me very good overall light that I can then supplement with task lighting when necessary. The tracks for the garage door create an installation challenge that has to be worked around, but I don't believe it will be an extreme problem. How to work when the door is up and blocking light is a bigger challenge, I think.

Looking at the numbers and the layout, it seems like there is a huge jump in coverage. I think i read on the Lighting thread that 75-100fc was the range i should be shooting for in a workshop. So using a single fixture type i get either what seems like a low end solution, or mass overkill as 110fc+ seems to be too much.

Opinions and ideas are greatly appreciated!

Don,

As you might have ascertained from the Visual program, you'll get a more even light spread with a 2 - 4 bulb fixture and more of them than 6 bulb. The real thing to pay attention to is the lower foot candle numbers between the fixtures. That's where you'll run into shadow and what you're really designing to, other than where you know you'll use task lighting. I hope that helps. Feel free to PM me and we can get a phone conversation going, if you need. By the way, I get plenty of light in my 30 x 40 shop with 3 4 lamp fixtures with the crappy diffusers per row spaced at 10' between the rows and 8' between fixtures. They start end to end about 5' of the walls and side to side ~ 10'.

Vic

  • Author

I see what you mean about the lighting contours. I played with the program a little more and ran it all the way thru to where it plotted out the values. I can see where the shadows are starting to creep in. I can also see what you mean about the 6-bulbs, 200+ FC right below the fixture but they fade out quickly...so that's out for sure, not to mention the $83 price tag ($75 after military discount). I went out into the shop and took some measurements for the location of the door tracks. There is also an attic ladder that will have to be worked around, but i don't intend to do any work in that general area, so it may not be too much of a problem.

Cool! Good luck with the re-purposing of the space! A shop is a really awesome space to have.

If you spend 5 minutes on google, you will see that lighting terms, formulas and calculations can get to be very confusing. You can avoid all of that confusion by following a very simple rule-of-thumb. For every 100 square feet of space in your shop, use 6 (six) 4-foot fluorescent bulbs. A 400 square foot shop (20×20) should have a total of 24 bulbs. This would be the minimum and a little extra would be just fine. Make sure you use diffusers on each fixture to reduce glare. Paint your walls and ceiling a flat white and keep your cabinets light colored as well.

  • Author

Vic,

I was in HD today to get some grout and paint (man I need to get a job, it seems like I've worked more in the week that I've been "retired" that in the past few months!) and detoured thru the lighting department to look at fixtures again. You mentioned diffusers - so should I be looking more at fixtures like this one:

http://www.homedepot.com/Lighting-Fans-Indoor-Lighting-Industrial-Shop-Lighting/h_d1/N-5yc1vZbvnq/R-100427376/h_d2/ProductDisplay?catalogId=10053&langId=-1&storeId=10051#.UOOqJKzNl8E

instead of the 4-bulb that I linked in my first post that simply had reflectors and a protective screen?

Vic,

I was in HD today to get some grout and paint (man I need to get a job, it seems like I've worked more in the week that I've been "retired" that in the past few months!) and detoured thru the lighting department to look at fixtures again. You mentioned diffusers - so should I be looking more at fixtures like this one:

http://www.homedepot...51#.UOOqJKzNl8E

instead of the 4-bulb that I linked in my first post that simply had reflectors and a protective screen?

Those are the exact fixtures that I have in my shop Don. I have 9 of those, 1 fixture that only has 2 bulbs in it, and 4 recessed flood lights that are installed in a soffit. Some quick math shows that I will have about 130 footcandles in my 432 square foot shop.

Don, the diffusers are going to reduce your lumen output, as they bounce quite bit back into the fixture. I'm not saying you shouldn't use them, but the do reduce the efficiency of the fixture. Depending on how good your dust collection system will be will determine how often you'd have to clean the lens. I've never cleaned mine and they're doing well. I'll probably clean them this next year, as I'm changing out my 4100K to 5000K. I'm not worried about going to full spectrum, as I've spent a lot of time under 5K Kelvin and it's perfect for my vision at this time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.