Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

miter saw fence

Featured Replies

I need some advice/ ideas. I rebuilt my miter saw station. On my old miter table I was able to the kreg fence. What I need help with is coming up with a way to use the kreg fence.

Sorry I can't upload a pic. Bit the new miter station. The saw sits below thesides. The old one the saw sat on top of the table.

  • Author

The saw is right were I want it. I need to attach something that is inline with my miter saw fence. But be able to use the kreg fence. Like Bart did here.

As my shop has progressed I have changed my setup several times making each one better, I used to have a fence that ran the length of the support but now I just use the factory fence on my saw which is pretty large. This does a few things, first, which is why I did it in the first place, it opens up the side supports to be used as a work surface which I love because when I have several pieces to be cut I place them there. It makes setup easier because you don't have to have it set perfect with e extra fence, I still do because my RAS is next to it. It also makes cutting safer. If you have a board that has isn't perfectly straight (if its off just a little this can be a problem) and you cut it, if it's touching the fence at the ends but not in the middle as it cuts the action from the blade will cause it to pull the board on each side of the blade center to the fence as it is almost through the cut which can bind the blade. I use mine for some rough cuts and finish cuts as well so this is my preference. The length of the factory fence is plenty long to allow you to register off of. As for the stop block and the ruler, I used a t track on the bed of the support. This may not work for you but I know I am much happier since I stopped with the fence. If you would like to see my setup look here. http://www.thewoodwhisperer.com/viewer-projects/nates-shop-projects/?project_type=shop-projects-2

  • Author

Journeyman:your idea will work. Since I only want to be able to make repeated cuts. is the t track just every day t track from rockler? Did you use a router to cut the grove? Is the t track in line with the fence? Or does it matter?

Well I'm not Journeyman, thats just the status title the forum gives, but yes mine is a Rockler T-track and for holding the ruler I cut a shallow dovetail in a piece of stock to allow the ruler tape to clip in and then a mating dado in my miter station that allows me to inset the assembly. I can take a close-up pic if this isnt clear enough if you would like.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.