Spunjin Posted May 8, 2013 Report Posted May 8, 2013 I just got an 8" Grizzly Jointer and the infeed table is about 0.015" higher on the end than at the cutter head. I haven't found the manual to be of any help with leveling the tables. Any sources out there someone can send me to? Thanks. Sent from my iPhone using Tapatalk Quote
dwacker Posted May 8, 2013 Report Posted May 8, 2013 Before you stress out about it drop the table down to a cutting height. Put a straight edge on the out feed and across the infeed. Measure the gap under the straight edge across the infeed. It may just be rough ways where they max out the height. Quote
Spunjin Posted May 8, 2013 Author Report Posted May 8, 2013 I have the outfeed table parallel to the cutter at top dead center as far as I can see with a straight edge. It came from the owner that way. But the infeed table has a difference of 0.006" from the front of the cutter to the back of the cutter and the ends are a little bit higher than the cutter end. I have the depth of cut set to 1/32". Should I just run some test cuts and measure each end and edge to see if there is a discrepancy after planing the other face? Sent from my iPhone using Tapatalk Quote
Popular Post dwacker Posted May 8, 2013 Popular Post Report Posted May 8, 2013 Just face joint a board. Put your straight edge on it if its flat go build something. 3 Quote
Spunjin Posted May 8, 2013 Author Report Posted May 8, 2013 Great thanks. I have a table to build so I'll get started Sent from my iPhone using Tapatalk Quote
pghmyn Posted May 8, 2013 Report Posted May 8, 2013 My jointer out-feed table has a little discrepancy in it at the end. I have jointed a few hundred BF of lumber through it now and haven't come across any gaps big enough where I couldn't close them. For my level of woodworking, the amount of error I have is easy to work around. If I was doing this for a living, I would want something a little more precise. I knew what type of quality I was getting into when I bought the machine, and I knew I could work with it. I have the G0656P 8" jointer from Grizzly. Quote
Spunjin Posted May 8, 2013 Author Report Posted May 8, 2013 I'm using the G0586. Now that I just cut my finger working to get the knives set I think I am going to order the helix cutter head since its on sale on the Grizzly site. Sent from my iPhone using Tapatalk Quote
Spunjin Posted May 9, 2013 Author Report Posted May 9, 2013 Well since I don't have 220v access yet I decided to tinker around a little bit more. I came to these measurements on the infeed table with the at about a 1/32" cut: 0.033" 0.033" 0.035" 0.031" Satisfactory or should I tinker longer? Sent from my iPhone using Tapatalk Quote
bpatters69 Posted May 10, 2013 Report Posted May 10, 2013 I just got an 8" Grizzly Jointer and the infeed table is about 0.015" higher on the end than at the cutter head. I haven't found the manual to be of any help with leveling the tables. Any sources out there someone can send me to? Thanks. Sent from my iPhone using Tapatalk Check out the videos on the Grizzly site for shiiming a jointer. The process is fairly straightforward and it makes sense if you watch it a couple of times. The basic premise is to shim the cutterhead in relation to the infeed table and then shim the outfeed table in relation to the infeed table. Finally, if the blades are not in alignment with the set-up, you would make adjustments to the knives. Quote
Spunjin Posted August 16, 2013 Author Report Posted August 16, 2013 I finally got the 220V outlet for the Jointer put in. After a test run, I found that I was getting a high spot in the middle of the board and it seems to cut deeper on the side by the guard. After reading 3 different articles and watching 1 video on adjusting a jointer with dovetail ways, I decided to pick one method and try it. I raised each table to the max height and checked to see if they were coplanar. The outfeed table was only off by 0.006" at the back by the cutter head and the other corners were off by 0.0015". I guess there isn't a real issue with that is there? Next I'll try a few test cuts on the edges of two boards. Fine Woodworking has a video where the presenter says to lower the infeed to take a shallow cut and lower the outfeed table just a bit below the cutter head. Then match the two edges and inspect what is happening. Since I have the same issue as he did with the high spot in the middle, I assume I need to raise the outfeed table, recut, test, and adjust accordingly. If I continue to get a wedged board even after sharpening and replacing the knives, I'll try shimming the low corner of the outfeed table. Any thoughts? I am about to start the G&G Blanket Chest build and I don't want to waste any African Mahogany. Quote
CessnaPilotBarry Posted August 16, 2013 Report Posted August 16, 2013 Just face joint a board. Put your straight edge on it if its flat go build something. THIS is what matters with woodworking tools. Specs and measurements get completely blown out of proportion on the 'net... If specs were published, they would matter. Since they usually aren't for consumer and small shop machines, the real proof in the pudding is the results. If the wood isn't coming out right, measurements can be helpful for troubleshooting. If no wood has been machined, and go/no-go specs are not published, they aren't useful. That is all... 1 Quote
Spunjin Posted August 17, 2013 Author Report Posted August 17, 2013 If the boards being jointed are coming out bowed, then surely I can't proceed without seeing to fix the problem. I did the previous steps I wrote about in my last post and the jointer is now cutting very well. I milled 4/4 hard maple to 7/8" all flat square and parallel. Now I have to tend to the blades. I had a few track marks from the nicks. I think I'll upgrade to a helical cutter head in the coming months. Sent from my iPhone using Tapatalk - now Free Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.