Daniel Kuehl Posted June 24, 2013 Report Posted June 24, 2013 I am building a Walnut table for a cross display for my wedding day this fall. I drew up a few sketches of some ideas I had, but ultimately decided that what I wanted was a table that looked like the Stickley 603...except bigger. The design I looked at was from Bob Lang's book, and the table is only 20 inches tall and 18 inches diameter. I'm planning to make mine 30 inches tall and 24 inches in diameter. Since I'm already drifting from the original design, It's feels natural to go even further and do the legs a bit differently. I'll probably add some corbells at the leg too. I don't have any real plans to go on, but I've got a good idea of the size and design of the table in my head, and I figure I can just wing it from here. Here's a pic of the walnut I'm using for this project: These boards are a little over 6' long, 14" wide, and 7/8" thick...and I got them for a song! $25 for the pair! Nice lookin wood that probably would make a nice kitchen table. Seemed like a shame to cut them up....but I don't need that big of a table yet. Here's a picture of the table top glue-up: Letting it sit clamped up overnight. Planning on making a router trammel to cut the circle tomorrow evening. Quote
Daniel Kuehl Posted June 25, 2013 Author Report Posted June 25, 2013 Got a little bit more done in the shop tonight. First step was building this: This little jig took only 15 minutes to make. The actual size of the circle ended up being 23 1/2" dia. I wasn't too careful when laying out the holes for the peg, but I wasn't trying to get too close. I'm in the ballpark, and it will still look the same. I do have another circle cutting jig that is 6' long. That would have been too awkward for this small of a circle. I use the long jig for cutting inside arches (harvey ellis influenced), and I will use it later in this build. After I cut the circle in about halfway through the thickness of the panel, I carefully cut the rest with the jig saw: All that was left after that was to flip the panel over and use a flush trim bit in the router to clean up the rest of the edge: Care must be taken when making this final cut when you get to the "short grain" edges of the table top. If you run your router too fast through these areas it can take a big chunk off of the panel. I forgot this and tore a chunk out, but the table top is still workable. I may come back and put a bullnose around the edge to clean it up some more....but I'll save that for another day. Quote
Daniel Kuehl Posted July 2, 2013 Author Report Posted July 2, 2013 Over the weekend I made the legs and the stretchers that will support the table top. Everything went fine with those. I also made the bottom rails and ran into a few self-induced problems. Here's problem number 1: I didn't have the peg for the trammel jig secured well enough and it slipped while I was making the cut! I ended up just cutting the arc 1" deeper into the rails and it looked ok. The 2 rails cross in the middle so ineeded to cut out a notch in each so they would overlap each other. Cutting the notch in the top of the first rail was easy - set the blade height on the table saw and run the rail through in a series of passes to create the notch. Cutting the notch in the bottom of the 2nd rail was more challenging. I layed out the cut lines, then started the notch with the jig-saw. I used the chisel to clean up the sides. when I was tapping the chisel in to clean out the bottom of the notch - HALF OF THE RAIL SPLIT IN TWO!!!!. I just glued the 2 pieces back together, and hopefully the crack won't be noticable. I know now what i did wrong. I needed to have a back-cut across the grain before I try to hog out with the grain. Quote
dwacker Posted July 2, 2013 Report Posted July 2, 2013 Looks good, you will get it. One word of advice. Templates! 2 Quote
Daniel Kuehl Posted July 3, 2013 Author Report Posted July 3, 2013 I thought about that while I was watching the glue dry. Seemed like a pretty pretty good idea.... Quote
Daniel Kuehl Posted July 3, 2013 Author Report Posted July 3, 2013 The fix on the bottom rail looks good, and the crack is hardly noticable. The glued up split rail is the near one on the left. This is how the top rails for mounting the table top fit together. They are joined with a half-lap in the middle. And here is the dry fit before the glue-up. It's not often I have a project stay together like this without glue. I'm kinda proud of how well this went together. Looks simple, but was still pretty challenging. Quote
Darren66 Posted July 3, 2013 Report Posted July 3, 2013 Daniel, that's looking really good. I like the clean design; nowhere to easily hide mistakes :-) particularly like your honesty about what went not quite right and how you fixed it. Quote
Daniel Kuehl Posted July 5, 2013 Author Report Posted July 5, 2013 Daniel, that's looking really good. I like the clean design; nowhere to easily hide mistakes :-) particularly like your honesty about what went not quite right and how you fixed it. Thanks! It seems like every project I work on there's something that doesn't go according to plan and requires me to slow down and think about how to fix it. Quote
Daniel Kuehl Posted October 19, 2013 Author Report Posted October 19, 2013 Here's a picture of the final product: I used it only to hold the cross at the front of the community center at our wedding ceremony. And in keeping with the spirit of honesty and transparency in my mistakes on this project....I really messed up the table top. I really wanted to learn how to use a smoothing plane. This was my first attempt on a panel, and it went horribly wrong. I practiced on normal wood....poplar. I learned that there was a HUGE difference when planing figured crotch wood! There's tearouts all over the top of the table! I didn't freak out about it....I made it look as good as I possibly could, and made sure to put a white cloth over the top for the display and thanked everyone who admired it. I would replace the top someday, but I think I might just give it away and chalk it up to experience. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.