Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Need some spray finishing advice

Featured Replies

Up until today, I have done 99.9% of my finish work by hand (the other 0.1% being an intro to spay finishing class I took a few years ago at lee valley).

My question is regarding drips in the finish. Typically, I use a wipe on poly and if I get a drip I can easily wipe it up while applying the finish. If I am spraying a clear coat (water borne poly - specifically general finishes high performance satin) and get a drip, do I let it dry and sand it out after? Or is there something I can do while the finish is still wet?

Is it as simple as wipe it up and recoat the area?

If I do get a drip, it probably means that I am saying too heavy, and I can adjust that. I am new to spray finishing and want to be prepared as I am sure I will make a few mistakes along the way.

I will be spraying with an earlex 5500 2 stage spray station, if that is a consideration. I will also thin the poly about 10 percent with water.

Thanks guys. As always, I look forward to your replies.

I think your over thinking it. No dont touch the runs or sags until they dry. Dont even worry about thinning until the time comes. Check the viscosity of your finish and go from there. Maybe go get yourself some cheap minwax WB poly and a sheet of plywood. Tape off the plywood in 1/8th's and practice on each section. When your done with one side laying flat stand it on edge and do the others side. The best way to learn is to just do it.

Why wait for a project to get a run?  Get a piece of wood and make a run. Practice removing the run with a dry poly hair brush and pull the run out. You can also use masking tape. Once the run is out (thick area) hit it quickly with more finish. This will allow the disrupted are to flow out again.

The goal here is to remove the highest part of the mountain. When the run area has dried (whatever coat your working on) go back to the run area and block sand smooth to match the remaining coat layer. Careful not to sand through. Then apply your next coat as usual.

 

You can wait for the run to dry and sand out....but that is a real b*&ch :unsure:

 

-Ace-

 

Opps----edit....re-read the post.....drips????????  Why would you get drips? Does your gun have a runny nose? :) :) :)
 

A fresh single sided razor blade slices runs right off. Stand it up and use it as a scraper to finish off or remove a sag in two or three passes. Piece of cake doesnt even need to be completely dry, just bow the blade to slice. FWIW you can buy a run razor holder at any auto body place for about $5 but they are not necessary. 

If you have drips you are either too close, moving to slow (thus putting too much in an area), too many passes or have your needle turned back too much. It was taught to me to let the drip dry and scrap it off with a paint scraper and then sand. I was later shown with a razor blade and it works wonders. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.