Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

How do I Stain/Dye Maple Dark Colors w/o blotch

Featured Replies

I am in the process of staining maple for a Bar.  The bar top will be a like a cognac or mahogany color on maple plywood and the sides will be maple ply and 1x3's with an ebony stain/dye.  I know maple isn't the easiest wood to stain dark but it's already bought and cut and this color combination is necessary for matching purposes. 

 

I have tried the varathane ebony stain on a few pieces that have been sanded with 120 and 180 grit.  But it is blotching a bit and has taken 3 coats and still not close to the dark ebony I'm looking for.   I didn't want to use a sealer first to eliminate blotch because although I have done this in the past with success it does lighten the final product and I need this to be a dark ebony.  I also have used a sealer followed with gel stain on difficult wood but I'm worried that this method would be hard to do successfully on large 3'x9' pieces by rag or sponge brush without lap marks.

 

Is spraying dye the way to go?  Any suggestions will be greatly appreciated.

Spraying the dye works to get a even coat. When you dye maple that dark it is quite possible to get it dark enough to completely hide the grain so be careful.

  • Author

Thanks for the tip.  I will do test runs if spraying.  Do you have a favorite dye type or brand?  I've never used dye and couldn't find them at Home Depot or Sherwin Williams. 

If you are looking for "Dark ebony" I would use India Ink. I have used it sucessfully in the past. This is a project I did about 6 months ago. Used India Ink on it. I brushed the india ink on with a foam brush and left.

Also, you may want to sand to a higher grit to stop blotching. AT LEAST 220. Another trick I learned was to dampen the maple with water before applying the stain.

I sprayed Transtint with alcohol . Forget where I bought it. I raised the grain with water and then re-sanded 220 before I sprayed. Thin coats, 50% overlap and built to the color I wanted.

Red oak dyed black is awesome, you see all the grain patterns and texture then top it with a clear finish.

  • Author

If you are looking for "Dark ebony" I would use India Ink. I have used it sucessfully in the past. This is a project I did about 6 months ago. Used India Ink on it. I brushed the india ink on with a foam brush and left.

Pat, Thanks for response.  That's a great looking piece.  I should have used India Ink on the last piece we did.  It's hard to tell from the picture but It looks like India Ink gives a pure black masking the grain?  I want dark but still showing grain. 

 

Also, you may want to sand to a higher grit to stop blotching. AT LEAST 220. Another trick I learned was to dampen the maple with water before applying the stain.

Pat, I was worried that 220 would make it harder for my ebony stain to penetrate to get nice and dark.  I already applied three coats to the few pieces sanded with 180 and at it looks like I'll need two more coats.  Maybe the water or a pre-stain would make sense for the cognac colored bar top though.  I'll test that.  I think it might prevent me from getting a dark enough ebony though?

  • Author

I sprayed Transtint with alcohol . Forget where I bought it. I raised the grain with water and then re-sanded 220 before I sprayed. Thin coats, 50% overlap and built to the color I wanted.

Red oak dyed black is awesome, you see all the grain patterns and texture then top it with a clear finish.

The more I read, the more this seems the way to go.  When you say you built up the color do you mean additional coats?  I heard dyes will double your color with each coat unlike stain.  So you started out pretty light and built up with additional coats? 

Yes, build up with thinned coats is how you get consistent color to the level of darkness you desire. Then I used several coats of sealer before I sanded and was very careful not to sand thru the color,especially on the corners. After the first sanding it is smooth sailing to the final finish..

The trick is lacquer thinner and transtint with maple and poplar sprayed. Seal with hot lacquer. You can seal with lacquer even its not your top coat of choice.

You don't need blotch control products if you spray dyes. The key to a nice ebony is lamp black (carbon). India ink is fine for tiny projects and works real well. 844 Lamp Black pigment will net even better results. It's expensive so the easiest and cheapest way to get is to buy solvent lacquer and have it tinted black so you get the pigment for free. Thin the solvent lacquer with medium lacquer thinner 1:20 ratio 1 being the lacquer. Spray a fine misting coat without any build and you will have ebony.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.