Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

My new spray finishing setup (some questions)

Featured Replies

In the spring I got a Fuji Mini-Mite 4 and played around with until summer hit. Now that cooler weather is coming back I'm back in the shop and getting my spray stuff ready to go. I built a spray booth and table based on plans from Jewitt's "Spray Finishing Made Simple" book and DVD. 

 

Here is my spray booth that folds down to 4" thick.

 

IMG_0244.JPG

 

Behind it I have a fan sitting on top of my table saw (crappy phone pic).

 

IMG_0241.JPG

 

I've heard that some waterbornes and aluminum can have problems. I got the converter off eBay then bought a different size cups from US Plastics. So far it's working good. 

 

IMG_0239.JPG

 

Having a 2-car garage this is probably the best I can do for spraying indoors. I do have some questions:

 

1. My air filtration is behind my booth. Should I run it while spraying (the booth ran will be running of course)

 

2. When done spraying, should I immediately shut down all fans or keep them running?

 

3. The MM4 puts out some air and I get a fair amount of bounce back. Do you generally run with air wide open or close it some to cut back on overspray?

 

Having fun playing around with it and think I'm going to be a fan of waterbornes. Faster application, quick dry time between coats, low odor, and days to cure compared to months are nice pluses. It is all new learning so I'm practicing a lot with finish recipes and techniques.

2. Leave it running to ventilate your shop.

3. I have my air supply on my MM3 fully open all the time. If you are getting a lot of overspray, try moving closer to the fan or get a stronger fan.

You don't have even close to enough air movement. Although these set ups are ok for model airplanes and an air brush they really don't do much of anything spraying any thing of size. Be care with assuming its quick drying. WB is pretty slow and is easy to trap solvent and cause a blue cast. Folks complain about blue cast showing up down the road. It's not the finish its the guy holding the gun.

Looking good.  :)  A suggestion would be to put a pleated filter behind the blue one to catch more of the dry finish before it passes through the fan. The blue filter can be use as "pre" filter to catch the wet over spray. 

 

I run my overhead filter "after" spraying to clean the air once the finish has flashed. My overhead filter is shop made using an attic fan and produces a lot of air movement and dust can be an issue.

 

I shut my "spray booth" fan down after spraying so not to kick up more "shop" dust till the finish flashes.

 

Sorry can't help with the MM4, I use compressed air guns.

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.