Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Drying sitka spruce in a humid environment

Featured Replies

First post here and I'm a noobie, so be gentle...

 

I live in Kodiak Alaska where the only wood I have access to is oak ($9+ bf from the store), maple ($13+ bf), 1 x X cedar, or green cut Sitka spruce from a local sawmill.  The Spruce is $.90 bf or $2 bf for clear.   The problem is that it's all really green.  Since Kodiak is an island we get a lot of wet weather and very moderate temps (lows in the 20's in the winter and highs in the 60's in the summer with 80" of rain in the year).  Our humidity today was 93% and about 35 degrees all day.

 

The regular cut wood has a lot of knots in it and the sawmill just leaves them in piles (not stickered) outside.  He keeps the clear wood in a shipping container, stickered. 

 

Basically, is there any hope?  Is it worth trying to get some green, cheap, wood and trying to dry it even though we don't really get dry or should I bite that expensive bullet and buy the oak/maple and work with that?  Since I'm a beginner I didn't want to blow all my money on relatively expensive wood to learn on but I also don't want to get discouraged by working with wood that may not dry out for months, if ever, and even if it does it will have some kind of warping.   

 

If I do go with spruce, can I expect it to dry out?  I have a covered wood shed that has an open gable end and a slotted raised floor so there is air flow.  Could I reasonably think that getting some planks and stickering them in the shed will actually dry them out in a couple months even with low temps and fairly high humidity?  I probably won't get anything over 8/4 at first (probably closer to 4/4 to 6/4). 

 

 

Wood is only gonna get as dry as your environment.  If it's always that humid up there, the moisture content in the wood is going to reflect the moisture content in the air.  And even if you lived in a more arid climate, it would still take months to dry the lumber.  93% humidity in December?  Forget about it...you might as well look into building green wood projects.

 

If I were you, I'd buy some of the clear Sitka spruce (if you're planning to build some acoustic guitars...otherwise, what's the point?), and sticker it inside your HOUSE.  Then forget you have it.  Go out and buy yourself some kiln-dried lumber (you can buy online), let it acclimate for a few weeks in your HOUSE, build some projects (returning the lumber each day back to inside the HOUSE...don't leave it in your shop), and then in 2015 start thinking about that Sitka spruce again.  It will need a LONG time to dry out in your environment.

The rough rule of thumb for air drying lumber is one year for every inch of board thickness.  Longer if it's not in a dry environment.  If you don't have room in your house, I guess you could build a storage shed and install a dehumidifier.

Luthiers make dry boxes, and throw a small lamp inside, should help you dry your wood out a little better.

Wow, "moderate" is a loosely used term in your sentence, LOL

 

As Eric has pointed out it takes a long time for wood to dry. Being that you are on an island off of Alaska makes things a little more difficult to procure. The sitka spruce is a nice wood to work with, especially nice clear pieces. Try to get pieces from your sawmill in the dead of winter when the wood is less apt to be wet internally and then store it. If its roughly 1" thick, you can expect about a year to pass before the wood will balance out to your local average equilibrium point. This is not the same as fine furniture dry! But the wood should be workable at this point. Do a search of solar kilns, I bet they would work fantastic in your near 18 hours of sunlight in the summer, LOL. The key to drying wood is air flow, the greater the air flow the easier it is for the wood to loose moisture to the environment. Temperature has an effect also. I would bet that with the extremes of temperature that you have, no drying would occur for several months of the year as you lose too much sunshine and heat.

  • Author

So, from what I'm getting is that I'm in about the worst place in the US to try to dry wood!  lol  High humidity and low temps year around.

 

It sounds like my best option would be to buy the wood from the local store where it's already dry and surfaced, even though it's $10 more a bf.  Shipping wood here really isn't an option.  Once I say I'm in Alaska they start adding zeros to the shipping costs.

 

Thanks for the input!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.