Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Edge Jointing Not Coming Together. Me? The Jointer? Me?

Featured Replies

I'm working on the top to my first "big" table. A kitchen table commissioned by the wife. I'm milling up the pieces for the top right now. I ended up having to rip some wide boards to fit my jointer, the faces get flat, but then when I joint an edge and go match it to another jointed edge I have a slight gap an one end. This happened repeatedly, the gap is probably about a 1/64"-1/32". Though light clamping does get rid of it, it seeds like this is just asking for it to open up later. I've tried to pay close attention to my technique, making sure I was applying appropriate pressure on the out feed side. The edge is square the already jointed face.

 

A quick note about the jointer, it is just an older all cast iron  6" Ridgid I picked up off CL for $125, but up until now it's always severed me well, so I don't know why it would all of a sudden be so different. However I've never really jointer such long stock(60") on it. 

 

So has anyone got any ideas or experience with this? 

 

This is a near dupe of my LJ post, but I'm trying to rally some brain power here so I can get this figured out and move on. Thanks in advance.

I've read a few places that the slightest gap in the center is preferred because of how it makes the joint behave. If the joint were to split, for any reason, it would most likely happen in the middle of the top instead of the ends. My thinking is a joint splitting open in the middle would be much harder than the ends because of the glue on both sides of the assumed split.

Sounds like snipe to me.  This can happen if your cutterhead is not perfectly flush with your outfeed table, but sits slightly proud.  PB is going to confirm that if it's the trailing edge.

Sounds like snipe to me.  This can happen if your cutterhead is not perfectly flush with your outfeed table, but sits slightly proud.  PB is going to confirm that if it's the trailing edge.

I've never understood the thought of having your cutter head just BARELY proud of the outfeed table. I tried it, and it just left tiny bits of snipe every time.

 

Like you said, having the cutter head flush with the outfeed table is the way to go.

 

Take a piece of wood, put it over the outfeed table and knives, spin the knives by hand as if they were cutting normally, if it picks up and moves your piece, you need to adjust.

In general, having the OF table slightly below the cutter head will create will create snipe, having it slightly above will leave a bit of a hump a the end. I would try raising the OF table slightly and trying it again.  Be sure to check your jointed edge against a known straight/flat surface, not against another jointed edge that may not be straight. Otherwise, if a gap exists its hard to tell which side of the joint it is on.

 

When checking edge joints before glue up, I find it helpful to clamp one piece on edge in the vice and set the mating piece on top - edge to edge. You can then pivot the top piece a little and feel where it drags on the bottom piece. Ideally, you should notice dragging at each end. If it pivots smoothly, one or both of jointed edges is convex.  That is a bad thing.

 

I've read a few places that the slightest gap in the center is preferred because of how it makes the joint behave.

 

This is usually referred to as a "spring" joint and much preferred to having a gap a the ends.  The reasoning is that since moisture escapes easier through the end grain, the ends tends to move a bit more than the middle.  Any shrinkage will show up a the ends first, and could open a joint that is "pre stressed" at glue up.  A spring joint puts the pre-stress at the center where movement is slightly less. 

Generally your not going to close the gap created by snipe with clamps. Since you can close the gaps with clamp pressure its probably not snipe. Without additional information its impossible to say but it sounds like simple table fall off which is very common on short bed jointers. Snipe is only going to affect a couple inches and make more of a notch that can't be closed with clamps.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.