Jg2259 Posted February 21, 2014 Report Posted February 21, 2014 Hello, i bought a Grizzly G0500 8" jointer off of CL a year or so ago, and I've been struggling keeping the fence square at 90 degrees. I take my time squaring it the length of the fence until I have it perfect. I then set the stop bolt (which is poorly designed IMO), and after one light use jointing the face and edge of a couple pieces of red oak, being careful not to bump the fence, the fence goes out of square again. It's not off by much, but just a little is too much. Does anyone own this jointer and are you experiencing the same problem? Thanks for any help, Jim Quote
pghmyn Posted February 21, 2014 Report Posted February 21, 2014 To be honest, I wouldn't worry too much about the fence being a little out of square. If you are edge jointing, just make sure you make complementary angles. Any bit of difference from 90 degrees will cancel out the error when you put the joint together. For example, put two boards on your bench exactly how you want them to go together. Fold the two boards up like a book so the edge you want to joint is facing down. Essentially the back side of a board will ride against the fence, and the front side of the other board will ride against the fence. Quote
Eric. Posted February 21, 2014 Report Posted February 21, 2014 I hear ya, Brother. Same problem with my Grizzly jointer. Unlike Sam, I DO want perfectly square and I don't wanna mess with planning out the complementary angle deal. Good in theory, a total pain in the you know what in practice. I'll tell ya what I did with mine...I torqued the crap out of that handle. Then I checked it again with a square, and beat it down even harder with a soft-faced mallet. Hasn't moved since. Quote
Jg2259 Posted February 21, 2014 Author Report Posted February 21, 2014 Sam, I did that exact technique last week on my very first panel glue up. It came out perfect. I can't locate the joint even when I know where its at. But for other joints, where the mating piece is not jointed it may be an issue. Eric, I also did what you suggested, but it still moved. Maybe I didn't beat on it hard enough, but I feel I shouldn't have to do that on a relatively expensive piece of machinery. I am almost to the point og calling Grizzly tech support, but I'm not sure how much help I'll receive since I bought it used. Jim Quote
pghmyn Posted February 21, 2014 Report Posted February 21, 2014 90 degrees is 90 degrees, no matter how you reach it in a panel glue up. Complementary angles work for me here, but I don't want the impression that I'm sloppy. For visible edge work, or joinery, I am a bit more perfectionist in that sense. Do you ever plan on moving the fence from 90 degrees once you get it there? I'm taking a stab in the dark because I don't know how the tilt mechanism fully works, but maybe you can find some slack in a pin joint and add some form of a bushing. Maybe even if you are up to it, epoxy? If it's not going to be moved from 90 degrees, I'd throw some epoxy in all the pin joints I could find on the fence and see how that works. Or unless there is a better adhesive for metal, I don't know. Never done it. Quote
Eric. Posted February 21, 2014 Report Posted February 21, 2014 Eric, I also did what you suggested, but it still moved. Maybe I didn't beat on it hard enough, but I feel I shouldn't have to do that on a relatively expensive piece of machinery. You shouldn't have to do it, but it's not a relatively expensive piece of machinery within the world of jointers. Grizzly's are budget machines and sometimes ya gotta deal with a little QC sloppiness. When I say I beat on that handle, I mean it. I didn't hit it hard enough to break it, but I wouldn't be able to loosen it without tapping it with the mallet in the opposite direction. If that doesn't work for you, I'm not sure what to recommend other than permanently tack welding it at 90* and hoping you never have to adjust your tables again. Or call Grizzly. Since you're not the original owner, they'll probably just recommend you buy a new fence...with the same problem. Quote
Jg2259 Posted February 26, 2014 Author Report Posted February 26, 2014 I tightened it up really good and I will wait to see if it moves again before I take more drastic actions to somehow lock it in. I have never moved it from 90 and doubt that I ever will, but you never know. Thank you guys for the suggestions. Jim Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.