Recommended Posts

Posted

I have a problem with the above router. There is a significant part on it that I have been unable to identify. Yes, I checked the manual and I have asked Sears/Craftsman for help, but no help was forthcoming, so I'm hoping that if I post the picture here, someone will be able to help. 

 

I'm new to this site, but I'm assuming that the photo I've posted below can be opened and expanded. 

post-15406-0-64057900-1395963379_thumb.j

 

The part I need identified is the the part marked by the little yellow circle to the left at the top of the router above the word, CRAFTSMAN. The yellow circle is pasted on the knob at the top of the part. Below the knob is a black threaded rod which extends to the base. On the rod just below the knob is another black part. 

 

I know that the part on the bottom topped by a red knob is used to raise and lower the bit, but what is the function of the parts I am trying to identify?

Posted

Are you trying to identify the part because you need to replace it? Or are you just trying to figure out what it does?

Posted

That is just a cap on the top of the rod (not used). If you have the manual see page 35 Fig 28 and page 36 fig 28B 

http://www.searspartsdirect.com/partsdirect/part-model/Craftsman-Parts/Router-Parts/user-manuals/manual-downloads/Model-32027683/0247/0740000?modelNumber=32027683&diagramPageId=&documentId=

The link from Shaffer, the Plunge base diagram part #67 Knob,adjusting

PART NUMBER: 3123435000

 

"The Depth-Adjustment wrench

supplied is used to adjust the depth when the

router is fixed to the router table"

Posted

Also welcome to the forum.

I should say why it's not used. One of my routers is the Craftsman one step up from this one (the red top model Fixed/Plunge Base kit). The fixed bases most people would mount in the router table or use free-hand. The plunge base is used free-hand and never used in a router table if a fixed base is available. So this depth adjustment for under the table mounted router is not needed/use if using the router plunge base free-hand.

Posted

Are you trying to identify the part because you need to replace it? Or are you just trying to figure out what it does?

I'm trying to find out what it does and how to use it.

Posted

That is just a cap on the top of the rod (not used). If you have the manual see page 35 Fig 28 and page 36 fig 28B 

http://www.searspartsdirect.com/partsdirect/part-model/Craftsman-Parts/Router-Parts/user-manuals/manual-downloads/Model-32027683/0247/0740000?modelNumber=32027683&diagramPageId=&documentId=

The link from Shaffer, the Plunge base diagram part #67 Knob,adjusting

PART NUMBER: 3123435000

 

"The Depth-Adjustment wrench

supplied is used to adjust the depth when the

router is fixed to the router table"

----

The manual didn't help me, but I think your answer does. You seem to be saying that the column on the left, which is topped by a red knob, is used to adjust the height of the bit when using the router in an upright position, but that you have to use the column on the right, the one I'm asking about, when using the router in an inverted position. Furthermore, that when you use it in the inverted position, you have to use that long skinny wrench to adjust the bit depth. Is that right?

Posted

Also welcome to the forum.

I should say why it's not used. One of my routers is the Craftsman one step up from this one (the red top model Fixed/Plunge Base kit). The fixed bases most people would mount in the router table or use free-hand. The plunge base is used free-hand and never used in a router table if a fixed base is available. So this depth adjustment for under the table mounted router is not needed/use if using the router plunge base free-hand.

Okay, thanks. You have confirmed what the poster before you said. I now understand what the "mystery column" is used for. Amazing that no  one at Sears/Craftsman could tell me that. One even said that it has no purpose. I'm not lying. 

Posted

I'd just like to thank everyone who responded to my question. I asked the same question at another woodworking site,  but I was unable to post a picture there, although someone offered to identify it though discussion. That didn't appeal to me. I don't like conversations full of: "I already said that, No, to the right of the framis, You misunderstood, I thought you said...," etc. Another site hasn't said anything after more than a week of posting my picture and my question. What more can I say? I tried three woodworking sites, but only WoodTalk Forum was able to help. Thanks.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 59 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined