Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

CN Blotch control with figured maple

Featured Replies

Mark (and others).  I'm wondering if anyone recommends using the Charles Neil blotch control product when using figures / birdseye maple?  I am building a table and the wood I've found has a good deal deal of birdseye figure, but also a bit of standard maple in it.  I do have some of CN's product already, but given that I would like the birdeye to pop, I wonder whether this is the right thing to do?  FYI - I plan on using TansTint Vintage maple dye, unless someone has a better suggestion.

When you finish figured wood and the figure pops, that is essentially blotching.  So no, you wouldn't want to use the CN juice if you want the figure to pop.  Same goes for shellac or any other sanding sealer.  However, you can put the TransTint in shellac, apply, sand back, then top coat.  That will pop the grain.  I've never used the CN blotch control stuff so I don't know if you can dissolve dye in it.  Is it alcohol based?

It's a water-based product and you probably could put water-based dye in it, though I'm not sure how that would all pan out. Ultimately, like kiki says, I'd avoid any form of blotch control on figured woods as it negates the figure. Usually, if there's some background blotching, it won't be noticeable if a pronounced figure exists. Test boards will give you a much better idea of what you're up against.

Because maple is prone to blotching, you really don't want to dye the stick if the birdseye is not consistent -- what you'll get is poped eyes and blotch everywhere else. In these sort of mixed-bag figure, you just better-off oil-based. I know lot's of folks like WB, but this isn't one of those cases...

Two words - Test Board.

I like the Transtint in shellac as a way to pop the grain but you should test it out first.

Maybe experiment with diluted CN sealer or try one coat rather then two he recommends? Test board vote also.

The product does work well on birds eye, one of the things it does, is to prevent bleed out around the eye's, often one coat is all you need if your looking to maintain the figure, it just doesn't blotch  and bleed out as bad, but rather makes the eyes more pronounced. If your trying to mute the eyes then 2 coats and possibly 3 may be needed, the area around the eyes is very absorbent. The issue with multiple coats is your losing color retention , as with any presatin, so multiple coats of dye may be needed to get the color, unless your spraying the color on .

 

As stated  above, you really need to test, because also as stated, mixed woods can be quite a challenge, especially when figured and non figured are incorporated into the same panel .

  • Author

thanks all.  testing pieces will be a part of the plan.  I think i will start with one CN coat.  Given that it is a mix of figured and non-figured, perhaps its best if the eyes don't pop too much anyway - otherwise it will scream that I'm using mixed boards.

 

Seperately, given i have mixed boards, I was planning to have a slight bevel on the top / long sides of each plank before glue up (maybe 1/16 radius).  I was concerned that not doing so and having a single wide flush table would be a bit odd given the mixed boards, and having a bevel would make the distinction part of the design - sort of like a farm table design.  Do you all think this is necessary? Or should I make the boards all flush.

  • Author

Should have thrown in a special thanks to Charles Himself!!!  Man this internet thing is amazing for connectivity.  

  • Author

Charles (and others).  I read your book and noticed a single sentence that says to be careful about shellac over the water based dye layer after using your blotch control.  I do NOT have a sprayer, and was planning on using a 1/2lb cut of shellac over the dye.  Is this something I need to really worry about, or should I change to an thinned oil instead of the shellac?

 

Seperately, you make mention of putting water down on boards before using a water based stain (or oil), as a way to prevent blotch.  You do not mention in the book whether this can be done in addition to using your blotch control or not.  Can you clarify?  I would think that since this really doesn't involve any friction to rub the blotch controller, this may not be a problem, but then again, why not ask the experts.  

the issue is like on like, the alcohol will act like water, and often water base colorants can be redissolved by water, the blotch control doesnt matter, it can do the same on raw wood, the mechanical pull of hand applying can pull color, a thin oil would do best but you want a good drying oil we like Arm R Seal by  General finishes, it goes on well and dries quickly .

  • Author

Got it.  WIll be using the Arm-R-Seal rather than the shellac

 

curious though on your thoughts about dowsing the boards with water just prior to adding the water based dye?  Your book suggested it would help limit blotch, and if done right before adding the dye, then there wouldn't really be much if any additional like on like situation since i'll be flooding the board seconds later with water based dye.  

 

maybe i need to shut up and just make my sample boards!

Jimmy,

 

Water can be be used as a blotch control to some degree, but remember if you wet the board then use a water base dye over it odds are it wil be much lighter , so you may have to do a second coat of color.Water does help with blotching but its not perfect.

 

We actually use water as a prestain then float a oil base top coat over it, to keep the oil from migrating into the soft grains and causing blotch, might sound a bit odd , but it works. Discovered it quite by accident, then did alot of testing and it worked well, the key is to use a good drying , varnish oil .

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.