Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Simple Stand for Spray Finishing Long Moldings

Featured Replies

This is the first time I have ever shared a solution with my fellow online community.  I uncovered few ideas as I researched this topic prior to beginning the work, so, I resolved to snap some pics and write a post in the hopes that other woodworkers/spray finishing enthusiasts could benefit from my experience in this situation.

 

Faced with the challenge of spraying three 16’ long sections of both chair rail and base board, I needed a way to hold the boards off the ground (to avoid introducing contaminants and working on my knees), and at a slight angle from 90 degrees (to ensure stability, and avoid the inconsistent finish that results from a starved, sputtering cup gun).

 

In conjunction with some shop made saw horses, these simple, angled stands did the trick quite nicely.  Once clamped into position, the stand’s screw pierces the MDF on the unseen back-side of the molding and allowed for a solid grip and minimal spray fan interruption.

 

Additionally, I learned that instead of walking and spraying down the entire 16’ length that better, more consistent results were achieved by mentally dividing the long boards into 2’ sections and covering the area in overlapping passes.

 

I have attached three pics to better illustrate. Hope someone out there finds this useful someday.

 

miw!

post-14345-0-93857000-1399092763_thumb.j

post-14345-0-68439100-1399092777_thumb.j

post-14345-0-30229700-1399092787_thumb.j

Nice jig for spraying trim!

I came up with a little jig for spraying small parts without allowing them to tip over or fly away. Some of these parts had to be finished on both sides. I traced the part on a 3/4" plywood scrap then grabbed my nail gun with 1 1/4" nails and put a pattern of nails just inside the lines. Then I switched to 1 1/2 " nails and shot a row outside the lines. I placed the part in the nest of nails and sprayed one face and all 4 sides without the part flying away or tipping over. After it dried I flipped it over and sprayed the other side.

The newest version of painters pyramids have tabs and screw holes. You can attach them in pairs and screw them down. I have used a row of these pairs to spray quarter round and other narrow strips by laying them in the Vee between the pyramids. A 2 1/2" by 5 " scrap of ply provides enough weight to keep the pyramid from flying away under the force of the spray gun.

I just noticed your neat stand for the spray gun. I just have a loop of wire hanging from my turbine. I also have a loop of wire it a couple of other places so I can hang the gun up when I need my hands free.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.