Recommended Posts

Posted

This is my first post on this forum. Let me start out by giving you the rundown. I have all of the general tools that you need for a shop;

12" DeWalt planner, 6" bench top jointer (need upgrade), 10" craftsman chop saw, 14" general badsaw, a bench top disc/belt sander, router table, my pride and joy; a 1978 craftsman 10" radial arm saw that I got in a box with no directions from a retiring cabinet maker in CO and brought back to life, all of the handheld power tools, handheld traditional tools, my now old craftsman 3hp contractor tablesaw, and a PSI canister DC plumed around in 4" PVC for my dust. I recently graduated college and my dad bought me a Grizzly 5hp 3 phase 52" tablesaw model G0652 for Christmas/ graduating. So now I have to completely rearrange my shop to get this bear into it (it's 91" x 75").

Now not to long ago my uncle's company acquired an old veneer plant so we decided to go take a few things they left behind. I got a 14' trailer loaded with quarter sawn white oak, cherry, black walnut, and a few other species. I also got a cyclone DC made by Dustkop. It's a 3/4hp 3 phase at 3450rpm

model 8C50-D1. Has a 5" inlet and 7" outlet push through design, but no filter so I would have to pipe it outside.

My question is should I hook up this new cyclone or change my canister to a 6" setup and run it. Like I said the Dustkop is a 3/4hp 3 phase at 3450rpm with 650cfm 10" impeller through 5" inlet 7" exhaust (exhaust would run outside since there is no filter). My current unit is a PSI 2hp single phase at 3450rpm with 2000cfm and 12" impeller (can have a 6" inlet, running 4" with a trash can separator at the moment) and a 1 micron canister filter. Should I switch out the units and just use the cyclone? Maybe use a combination of the two? Or just change my PSI to a 6" ducted setup instead of the 4" ducted setup and make a 6" separator?

Posted

There’s a lot going on in this post… It’s a bit hard to get through… Can you simplify the post by removing extraneous information and reformat it?

 

A good start would be a simple list of equipment and their CFM requirements…

 

A sketch of your shop with eqpt positions and rough dimensions would help…

 

An idea of the duct runs – diameter, length and complexity (elbows, bends, etc) would help

 

Off-the-cuff, no hope that a 10” impeller setup can generate CFM at a usable pressure to do much for your tools…

 

A 12” impellor is better (but still very limited), and may work if the runs are very short… A 6” inlet DC setup is very limited by the amount of ductwork it can drive… Just ignore the 2K-CFM and RPM numbers -- not really imporant...

Posted

12" DeWalt planner, 6" bench top jointer, 10" craftsman chop saw, 14" general badsaw, a bench top disc/belt sander, router table, my pride and joy; a 1978 craftsman 10" radial arm saw, and a PSI 2hp canister DC plumed around in 4" PVC for my dust, a Grizzly 5hp 3 phase 52" tablesaw model G0652.  The new Tablesaw is 400 CFM but the rest of the equipment I'm not sure of, they are older than I am and the badges on the tools don't say anything about dust collection. The runs wouldn't be more than 20 feet with an elbow or two to drop down. The PSI with 12" impeller is doing 30 foot plus runs now and works just fine but it was put in the corner as an after thought where I'm going to change locations around now and put the DC in a central location. If I use to PSI I will be running 6" trunks with 4" drops, If I run the Dustkop I will be using 5" trunks with 4" drops. I've built a sketch up in Grizzly's workshop designer but I'm not sure how to save it right to get it to the forum.

Posted

Sorry I am not 100% sure what you are trying to do. That being said, chances are good you will want to run both dust collectors. The longer the pipe between your machine and the dust collector the harder it has to suck. So use one dust collector for one part of your shop, and the other machine for the other end of the shop.

Posted

There’s still a lot of confusion as to what you want to do… Let’s start again without narrative. Just the facts mam…

 

You can use the ‘full editor’ option and attach you image as long as its 1.4Meg and under…

 

Let’s get a simple list of your tools, a sketch of how they are arranged.

 

After we get that, then we can get to your goals…

 

Something like:

 

Tool             Inlet size   CFM    Distance from DC      Num Elbows
-------           ------------ --------    ------------------------ -------------
Table saw       4”            400           20’                           2

 

 

If you don’t have the manual, go to the company’s website and download it. For things like Radial Arm saws, you need some sort of hood-capture, so just list the tool and distance, but forget the CFM.

 

If the tool is to be replaced, list what it’s going to be replaced with under the entry and get those specs from the mfg website…

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 45 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined