Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Current Basement Shop and Suggestions

Featured Replies

So I've started to look hard at putting some logic to the layout of my "shop". Trying to build a space where I can do a bit more than the minimal dabbling that I'm doing now. The attached shots are slightly messier than usual, but as you can see the space isn't utilized very well. The ceiling in the basement is mostly about 78" high, but the ducts/joists drop down under 72", so I'm really hemmed into the space. The area is roughly 12'x14' maybe?, but the furnace and chimney take a chunk out of that. I'm planning on going down there tonight and griding the space off with what I have there now.

 

In the left corner of both photos, there's a large flat file and old drafting table that serve as a workbench/crap collector for now, but I'm in the process of building a knockdown workbench to replace those. I also lack any decent shop tools. Currently, my shop-away-from-home is my Dad's setup, but that requires a 40minute drive anytime I need to cut anything I don't trust to a straight edge and circular saw on a couple of horses. I'l like to fit a tablesaw and outfeed table of some size into the plan. Since this is a shallow basement with a narrow staircase, I'm not going to be making anything large.

 

Any tips/suggestions for how to improve this space would be great.

 

 

My dream shop (in this house, at least) would be to dig out the crawlspace under the addition, go down an additional 3' so I can have some head room and install a set of bilco doors on the back of the house, so I don't need to drag all my materials through the house to get to the basement, then install a door where the access hole is now so I can stop stinking up the entire house every time I paint/stain, and covering the laundry with sawdust when I sand. But for the cost of all that, we might as well look for a new house.

post-16855-0-94249300-1421848833_thumb.j

post-16855-0-96143500-1421848838_thumb.j

Perhaps removing the table you have now adding a small cabinet saw and an out feed table that doubles as your work table.

 

Fact is that you just don't have much room so having your out feed table serve multiple functions might be the way to go.  Drop a vise or 2 on it, maybe some hold fasts to t-track in top, some storage under it to utilize all the space.. 

 

Welcome to the forums!

  • Author

Thanks guys, I forgot to ask about doing just that. I was thinking about setting up the work bench to do dual duty.

So not to sidetrack my original post, but I've never used a table saw before. Does it require clearance on all sides or am I alright pushing 1 side up to the wall?

I grew up using the 10" craftsman radial that my grandfather had set up in my dad's shop. It's literally been the workhorse of the shop. Only saw they've had, I think maybe 1 board has kicked back, so I never saw it as a dangerous machine. Low and behold, I come online and find out that everyone seems to hate them. So the question is, is the better saw the one you have experience with/respect for? Or is it the one that is highly rated/reviewed?

Many people push them towards a wall but, my preference is to have access all around.  Your shop size could make that challenging.

 

As for the saw, it's a matter of accuracy, preferences, and price range.  Once you get above the "contractor" levels, the accuracy improves on most saws so it then becomes preferences and price range.  Frankly anything from Grizzly to PM and Sawstop in a hobby shop will keep you happy for many many years.

  • Author

Hmm, that's something I hadn't though of. Stupid question, what company is PM?

I use a cheap contractors tablesaw and build a large multipurpose table in my basement shop. I just order hardware to install a router, lift, fence, dust collection in the far end of the same table

post-16388-0-83000100-1421862865_thumb.j

As a general contractor I have replaced basement walls and put a couple basements in where there was none before, it's not cheap but it is doable.

  • Author

Thanks, that looks like something that could work for me. I hope to extend a bit further out into the rest of the basement. The basement is about 27' from front to back, so I'm thinking I can creep into the front area a bit.

 

As for doing that basement expansion, I doubt I'll ever free up enough cash to warrant that, I've got enough work to keep me busy in the rooms I already have without adding another! The addition is roughly 200sq ft, about 3' of dirt to remove to get level with basement, another 2-3' if I want a full height ceiling, plus new foundation, electrical, insulation, HVAC and modifying the radon removal system. I'd say roughly, $18-20k, plus a bit more for headaches? I'll stick with the space I have until I can make some money off the hobby to defray the cost.

Yep, either you have been checking in to it or thats a pretty good guess, that sounds pretty close but of course it's going to cost more in New York than it would here in central Indiana.

 

If you are going to be there a while you could possibly help the situation just buy making an outside entrance to the basement, you could probably do most of that work yourself.

 

I think if you do much work down there, establish a good work flow, you will find you can do more in that space than you might think.

  • Author

Semi-educated guess, I think the same layout would work out in both spaces, so I'll refine it in the space I have and overplan the "expansion".

I have recently moved to a small shop from a very large one (230 sq feet or so from over 1800). I have been very successful in the transition, but it requires some compromises. So far I have:

1 - removed ALL non woodworking items from the shop
2 - hung my single stage DC on the wall to eliminate the stand
3 - bought the highest quality cast iron TS wing available with a router cutout, and sold the router table
4- used my workbench as my TS out feed table
5 - bought some festool gear to "systemize" more and improve workflow (CT26 is great for this)
6 - being good at not storing too much extra lumber

Future items:

7 - adding a kapex to reduce my current bosch CSMS setup

  • Author

Thanks, thats a lot of help. Late last night, I took a bunch of measurements and am going to put together a layout in a bit. One thing I haven't really noticed before is the lack of outlets. Mostly I have hand and battery powered tools, and I've run an extension cord for the shop vac and router. There is a 220v outlet on the other side of the back wall, unused dryer outlet I assume since the dryer that is there is gas, so I can have that moved if need be. As for 110 outlets, need to have someone look at how much room is left on the breakers.

  • Author

Pulled together a bit of a drawing. The left is my current setup, in relation to the rest of the basement. Right is my thought on what to do with the space. One foot grid on the drawing, for placement sake, I just pulled the dimensions for a couple of pieces off of Grizzly's site. I'm probably going to end up going the "previously loved" craigslist route for this set of machines.

 

To break it down a bit, I assume that while pushing material through the saw I will be slightly stooped over. I'm 5'11", so I just need to duck my head a bit to operate. I'll feed the boards out onto the workbench I'm building. (I was able to pick up several sheets of nice plywood and a small pile of 2x4s from one of the shipping departments at work, so I thought I'd start simple)

 

In my dad's workroom, we had the band saw (until it bit the dust) and drill press next to each other as extra support surface, figure that should work here too. Three feet is the spacing they use for the machine shops at work, so I figure that's a good amount of space between the bench and back two machines. 

 

Next to that, I'm thinking I'll just go the low tech route for now and use a box fan with furnace filters on both sides and blow into the crawlspace access. If I set it up right, I can use the open area around the fan in the access hole as a return vent of sorts, allowing filtered air back into the room.

 

Existing ancient bench that was in the basement when we moved in will take a trip out to the garage as a potting bench. Drafting table and flat file will relocate to the other side of the basement, separating woodworking space from craft/design space.

 

Existing shelving units will be repositioned and I'll secure a dividing wall behind them to isolate the washer and dryer. If the placement works out in the long run, maybe I'll stud and drywall it, but the more flexible I can be right now, the better.

 

As I said last post, I'll need to evaluate the outlets, currently everything in the basement is on the same line, and the rest of the house is a mix of wiring from 1925/1950s/1970s/modern as folks have changed things throughout the years. We hadn't even noticed that there weren't any grounded outlet on the second floor until I went to plug in my computer... but that's another story.

post-16855-0-27036700-1422050878_thumb.j

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.