Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Using120 grit on a random orbital sander equivalent to 180 grit finish?

Featured Replies

Hi,

 

I'm new to the forum so apologies if I'm not going about this the right way!

 

I've been using Osmo rapid polyx oil for years with excellent results and thought that after 10 years of using the same product i should check out some of their other options. They had one specifically for use on kitchen worktops which I thought would be perfect for finishing a beech sink worktop but the results were very disappointing... After the client using it for just a couple of weeks it started to show water marks from the tannins in the wood coming through. It had 4 thinly applied coats so really shouldn't do this. The client says they have been quite careful about wiping up excess water but it's a sink and no ones perfect and there are several rings of the blue tannins where they have left glasses etc. I've attached a photo showing the damage.post-17977-0-12418500-1432903715_thumb.j

 

I've never had this from the Osmo Rapid I usually use so I contacted Osmo and they sent a rep down to have a look at it. He agreed that it should have been protected but implied that it was the fault of the client leaving wet items on the top. This is fair enough but the level of damage is, in my view, too great for the client to take all the blame.

 

The question I have relates to the next excuse he made which was that I had sanded it with too fine a grit. I had followed the instructions on the tin exactly, which advised sanding to 120-150 grit. His startling claim was that using a random orbital sander with a 120 grit pad actually achieves a finish of about 180 grit and sanding with a 150 grit with a random orbital sander (which I did) will give a finish equivalent to 220 grit.  He said that sanding with a belt sander will give the same finish as the grit you use, i.e. using a 120 grit belt on a belt sander will give a finish equivalent to 120 grit. His point was that the random orbital gives a smoother finish due to the random orbital action...I have never heard this before - has anyone else? 

 

Any thoughts would be useful before I take it up a level with the Osmo management!

Thanks

Tom

I don't know about that claim specifically.   But do keep in mind that your 120 grit pad will start to act more like a higher grit pad as it wears down.  It might be good practice to take one final pass with a brand new 120 grit pad before applying the finish.  

==>His startling claim was that using a random orbital sander with a 120 grit pad actually achieves a finish of about 180 grit and sanding with a 150 grit with a random orbital sander (which I did) will give a finish equivalent to 220 grit.

Not the same at all... Apples and oranges... Scratch patterns vs glazing...

 

New (read as sharp) abrasive grit cleaves wood fibers cleanly – same with inter-coat scratch patterns... Worn grit doesn’t... The reasons are beyond scope for a Friday afternoon... A further factor is heat -- overusing dull abrasives adds heat to the system -- coatings hate heat... Especially if they are not cured...

 

So sanding with fresh P120, then fresh P150 is not the same as sanding with fresh P120 until it becomes '150-esque'...

 

Sanding too long with a dull abrasive matrix can glaze a surface...

 

So the long and short of it... the representative isn't exactly correct, but not completely wrong either... I've never used the finish in question, so can't speak to voracity of the representative’s claim – overusing an abrasive isn’t the same as using two fresh abrasives – but that may or may not impact the finish -- depends on the wood and the finish... Sorry I can't be more help.

 

There's a more detailed thread on this floating around --- you can google it, if interested... It gets into friability, microns, abrasive type, etc...

  • 11 years later...

@Ruby Tian Welcome to the forum. You've replied to a thread that is 11 years old with participants I don't see much any more, so you may not get a reply.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.