Recommended Posts

Posted

I've just purchased a PC4216 dovetail jig and the PC690LR router (new to routers BTW).  I have put the 3/4 dovetail bit in the router and pulled out about 1/16 from collet like is recommended and attached the screw on guide bushing to run in the template.  When I power on the router I see sparks that are coming from between the bottom of the screw on lock ring and the collet.  Apparently these two are rubbing together.  What's wrong?

Posted

So the collet from the router is rubbing on the guide and sparking? Have you set your depth of cut yet for the router bit?

When i used my 4200 series jig i have to have the bit pulled out so i can plunge my router (890 series with plunge base) with out the collet touching the guide. The mark i use for setting the bit in the collet is the text on the PC bits. I make sure that all of the text is inside the collet or about 3/4" of the shank. If i go to far i bottom out, not far enough the bit could slip. Using this method I've cut a lot of dovetails and box joints with no issues. I honestly like Freud bits because they draw a line for minimum insertion. Just doing some quick research 3/4" for a 1/2" bit appears to be listed as an "engineering minimum" what ever that means.

Look at it this way some one designed this jig to work and work somewhat safely (with power tools there is always some danger) so you may have to edge the bit out until you no longer make contact with the guide.

Posted

That's what I was thinking but it says pull out about 1/16. When I do that and set the depth according to the dovetail jig, the locking ring is sitting on the collet every time.  I just wasn't sure how far I could safely pull the bit out and leave enuf shank in the collet to hold the bit safely.  Thanks.

Posted
36 minutes ago, Vader said:

That's what I was thinking but it says pull out about 1/16. When I do that and set the depth according to the dovetail jig, the locking ring is sitting on the collet every time.  I just wasn't sure how far I could safely pull the bit out and leave enuf shank in the collet to hold the bit safely.  Thanks.

Pulling the bit out 1/16 after bottoming out just ensures you get full tension on the bit with the collet, since while tightening the bit it is drawn in slightly. You don't want to bottom the bit out or you won't get the collet snug.

In most cases you can get away with pulling the bit out further. The best way to approach minimum insertion is to insert the bit into the collet before you chuck it up so you can physically see what's grabbing. Typically, you want the bit to be atleast through the grabbing section of the collet. My Festool router has a deeper collet than my PC router so there is more room for adjustment.

Whenever I feel I am border-line I do a quick trigger pulse on the router. If the router is vibration free, and you are good and snug, you're in okayville.

If there is a line on the bit, that's the manufacturer saying we recommend this! But in the real world that doesn't always work. 

You have to ask yourself this. What is safer, backing the bit out some or having it bind, throw sparks and potentially break from it overheating and stress, flying out like shrapnal. I'd back out the bit some.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 66 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined