Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bevel Sled Rebuild

Featured Replies

  • Popular Post

This is a rambling tale so feel free to skip ahead. I got lazy and left the HVAC weep drain termination point (small outdoor French drain) stay on the "To-Do" list too long. Result? Weeds grew around the end of the pipe, dirt collected around the weeds courtesy of the wind and the end of the pipe got buried. The drain tube filled up and the inside unit dripped inside . . . right on the bevel sled that was hanging from the cleat peg rack. I knew I shouldn't have run cleats under the unit but I wanted the space :( . Fixed/finished the drain but the sled was trashed.

I needed a bevel sled the other day and I am still waiting for finish to cure on a current project. Our bout of weird weather really altered my usual finishing protocol timeline.

I told you it would be a rambling tale . . .

Be that as it may; I dug an old small scale sled of dad's out of one of the outbuildings to see if I could recover it. With the current cost of BB ply I am more prone to up-cycle discarded items lately.

The sled was scaled for dad's old Zip Code saw so the runners and deck would need some love. Once I pulled the front and rear fences I was left with two panels that were just a smidge shy of what I wanted. I added some strips of ply and then glued everything up just like any other panel glue up.

BevelSledRebuild(1).thumb.jpg.a9337ef093d74ab12c9c57e998ee62ff.jpg
I epoxied strips of scrap into the kerfs in the dummy-block . . .
BevelSledRebuild(2).thumb.jpg.e52f46043a47f8a2ccebbef8b7ab68b1.jpg
. . . and the front fence.
BevelSledRebuild(3).thumb.jpg.12e13ca7f01c1d411f5d3dafebb0e058.jpg
Dad's version did not have replaceable inserts. There was some discussion in another thread about making jigs do multiple jobs. Replaceable ZCI's in sleds lets this happen. I don't have room to store half a dozen one-trick-ponies. I use a router and a dado jig to cut the 3" wide recess for the ZCI.
BevelSledRebuild(4).thumb.jpg.a4470943ce164b5250bf2ba559cdd03e.jpg
I then temporarily place the fence and layout the dado for the fence.
BevelSledRebuild(5).thumb.jpg.610b7dd90cb9bd1ec71e64cb1aa75cad.jpg

BevelSledRebuild(6).thumb.jpg.4f1ced34e0b5fa1d62e6427230ed5690.jpg
I have to cut a 90 degree position to allow me to use the 5-cut method to align the fence. I do this without the inserts in place.
BevelSledRebuild(7).thumb.jpg.c34f017c60a4b59d437f584cb67cafb6.jpg
I found that the fence would not adjust enough to get me well aligned. I turned the 3/8" holes into 3/8" slots at the drill press. I use the original hole to line up the bit position and place the fence and a stop.
BevelSledRebuild(8).thumb.jpg.6c7bf0db8350a963ee7bb3f27c48841a.jpg
The I slip a couple of 3/16" setup bars between the sled base and the fence to reposition the material.
BevelSledRebuild(9).thumb.jpg.bda8c0848354aae51d71fa8f3086e865.jpg
The result is a slightly overlapping set of holes. BTW, dad had t-track on his sled so I kept that.
BevelSledRebuild(10).thumb.jpg.ae5f956601ea435f04237338ef9e83bb.jpg
I chisel the holes into a slot. Now I have plenty of room to get things well aligned. Once I am happy with the fence position I install the inserts and make a 45 degree cut. 45 degree bevels will be the bulk of this sleds job. Other inserts can be swapped in and out for other angles.
I rip a piece of scrap ply to test the alignment at 45 degrees. I put on a couple of flip stops at random lengths, clamp down the scrap and cut my first bevel.
BevelSledRebuild(11).thumb.jpg.36e86094617927b9e85d47a08edb1bdd.jpg
I cut a couple of short pieces . . .
BevelSledRebuild(12).thumb.jpg.7abe628361209dd28f92f53b76164b23.jpg
. . . and a couple of long ones.
BevelSledRebuild(13).thumb.jpg.881afc5ed504c4b6cd8c020cad8ad28a.jpg
Like so.
BevelSledRebuild(14).thumb.jpg.5649954541f61f0d025903e4ec83ab73.jpg
OK, the miters are tight and consistent along all edges . .. success!
BevelSledRebuild(15).thumb.jpg.1c2e1675e70a92326735bde0e4702151.jpg
When it is not in use it hangs from one of the new batch of cleat pegs (on a wall that does not have an indoor unit on it :rofl:).

BevelSledRebuild(16).thumb.jpg.1e7a9ee8fb76684151f6e3775fb074c4.jpg

  • Author
  • Popular Post

Forgot to show the dummy block; very important. I usually attach these with long screws from the opposite side of the fence. With the sled's intended use of bevel angles I didn't really have any good locations that avoided possible blade positions. I went with pocket screws from the back. I just made sure the screw positions were in locations that the blade could never get to.
BevelSledRebuild(17).thumb.jpg.d7dbd883fbb9f4fd6cd5268967c66d6a.jpg
After drilling the pockets I place the block on a couple of business cards. This leaves just enough room to allow easy sliding of the inserts into the recess designed for them.
BevelSledRebuild(18).thumb.jpg.94db06590ef0e9dcca03754312c475f3.jpg
I add the screws, pull out the business card spacers and it's all set.  The fence, block and base will eventually get pretty chewed up due to different angles being used.  The replaceable ZCI's always present a good backer helping to give me a clean cut.

  • Author
  • Popular Post

I keep thin stock from resawing in a simple wall bin made from scrap that I tucked up over the edge sander.

VanityOrg(7).thumb.jpg.d5dcb95bbefe477dbc19ecf20a4d2e56.jpg

I grabbed some maple stock and made LOML a little sink-top "girl stuff" organizer to test out the sled.

VanityOrg(8).thumb.jpg.8b06bc88c8f740aa44b101e8b72706bf.jpg

She had been using a plastic drawer organizer to hold her tweezers, Q-Tips, and such for years.  Win-win.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.