Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

First River Table Project – Questions About Wood Placement and Deep Pour Epoxy

Featured Replies

Hi everyone,

I’m preparing for my first small river table project and would appreciate some advice from people with more experience.

The mold I’m using is approximately 60 × 30 × 10 cm. I plan to place two pieces of wood along the outer sides of the mold, with the straighter edges facing outward and the natural, irregular edges facing the center to form the river.

The wood will be close to 60 cm long and under 5 cm thick. I’m still deciding how much space to leave between the two pieces and how wide the river section should be.

For the pour, I’m currently looking at this deep pour epoxy resin, which is intended for thicker castings and river table projects.

Before I begin, I have a few questions:

  • Should I seal the live edges before placing the wood in the mold?
  • What is the best way to prevent the wood from floating during the pour?
  • Is it better to pour the full depth at once or divide it into layers?
  • How much extra epoxy should I prepare for uneven live edges and possible leaks?
  • Are there any common mistakes I should avoid on a first river table project?

Any suggestions would be greatly appreciated. I’ll also share some photos once I begin the project.

Thanks!

  • Popular Post

Welcome to the forum. I've not done an epoxy pour as big as what you are planning so others may chime in with better advice.

> Should I seal the live edges before placing the wood in the mold?

If you are adding any tint/dye to the epoxy and don't want it to seep into the wood, yes certainly. Otherwise I'm not sure it's critical.

> What is the best way to prevent the wood from floating during the pour?

I don't think I've seen this issue. If it is an issue my thought would be to put packing tape (or something similar epoxy doesn't stick to) on something heavy and use it on top of the wood for the first layer or two.

> Is it better to pour the full depth at once or divide it into layers?

Read the directions on the epoxy, usually it specifies a maximum depth. At 5 cm I would assume you will be doing layers.

> How much extra epoxy should I prepare for uneven live edges and possible leaks?

In my experience, assume you will have a leak :-) I think this is one of those situations you just can't estimate that precisely and you need to overbuy. It's better to have extra than to run out and you'll use it on your next project.

> Are there any common mistakes I should avoid on a first river table project?

Assume you will have a leak and plan appropriately in terms of where you set up your form.

Go slowly and takes notes as you mix your epoxy. With multiple pours, it can be easy to get distracted in the middle of a mix, forget where you are at and end up with non-hardening glob.

> Any suggestions would be greatly appreciated.

Bubbles in the epoxy will be a challenge. I use a small hand-held propane torch gently across the surface to release them.

> I’ll also share some photos once I begin the project.

Thanks! Looking forward to it.

Von

On 7/23/2026 at 8:19 PM, Ron Swanson Jr. said:

In addition to @Von 's good advice, i would suggest a practice run or two using scrap, so you can run through the entire process.  

+1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.