tprins Posted May 12, 2012 Report Posted May 12, 2012 I purchased a Jet 22-44 drum sander a couple months back and have been having some issues with it. When I got it the conveyor belt did not work at all, so Jet sent me a new circuit board. However, now the conveyor only runs from speed setting 40-100. From 0-40 it doesn't move (and yes, the indicator on the knob is set correctly...). I called Jet and they sent me another new circuit board but the result is the same. Is it normal for the belt only to move in the upper speed range? This is the first time I have used a drum sander so I don't really know what is expected. Thanks for any input! Quote
Eric. Posted May 12, 2012 Report Posted May 12, 2012 I can't give you any tech support on that machine, but if it were me...the whole thing would be going back and I'd be demanding a new one. Unacceptable. Quote
tprins Posted May 13, 2012 Author Report Posted May 13, 2012 I've certainly considered sending it back, but it is such a pain to setup a new machine I'd rather get the one I have working. I guess I'll be on the phone with Jet again on Monday. I will say that Jet's support people have always been quite nice, but I live on the west coast so it takes a week to get anything from them. Also their hours are quite limited. Quote
Sac Posted May 13, 2012 Report Posted May 13, 2012 I can't give you any tech support on that machine, but if it were me...the whole thing would be going back and I'd be demanding a new one. Unacceptable. +1 Brand new machine.. not working, time for a return... Quote
dwacker Posted May 13, 2012 Report Posted May 13, 2012 Have you tried running the conveyer on high for a few minutes to free up the gear box. The dc motor is to small if the gear box is tight. You can pull the motor and see if the speed control works properly with no load. Also make sure conveyer is not to tight. Don Quote
tprins Posted May 15, 2012 Author Report Posted May 15, 2012 Thanks for the ideas Don. I talked with a different tech at Jet and he said it was normal for the drum sander conveyor not to move in the lower speed range. It would have been nice if the first guy told me that. Quote
dwacker Posted May 15, 2012 Report Posted May 15, 2012 Doesnt seem right I had the 22-44 and the 22-44osc and both moved at lower speed if I remember correctly. Send Mark a message and verify, I think he has the 22-44 my memory is getting bad. Don Quote
TimV Posted May 15, 2012 Report Posted May 15, 2012 I talked with a different tech at Jet and he said it was normal for the drum sander conveyor not to move in the lower speed range. That seems really odd to me. What would be the purpose of that? Quote
CessnaPilotBarry Posted May 15, 2012 Report Posted May 15, 2012 Mine will move so slowly, you need to mark it to tell. If they keep responding, I'd work with them. You might need a motor. The 22/44 would be a pain to swap the entire machine. Since it's brand new, Don's suggestion has a lot of merit. The belt, bearings, etc... all probably have a lot of drag being brand new. Quote
tprins Posted May 16, 2012 Author Report Posted May 16, 2012 I finally did the obvious thing and checked the output to the motor with a multimeter. Neither of the working control boards put out any power until the knob is up to about 35. So the motor is fine, it turns on when the power comes on. I think I might have been unclear in my description of what is happening. The motor still comes on slow and then gets faster as the dial moves up. It just doesn't start moving until the knob is up a little ways. The tech at Jet said that most units start moving around 15 or 20, but it is not unusual for them to start a bit higher. The scale on the unit is, after all, arbitrary. Thanks everyone for your ideas. I am going to call this working and move on (need to finish sanding some panels...). Tim Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.