Eric. Posted August 16, 2012 Report Posted August 16, 2012 I'm fairly satisfied with my DC at the majority of my tools, especially for collecting chips and shavings. But Bill Pentz would probably have a stroke if he saw the amount of fine dust my table saw produced and escaped the DC. I'm not TOO concerned about it since I usually work with the garage door(s) and windows open and wear a respirator when things get hairy, and I'm not ultra-paranoid about particulates like some guys are...even if I probably should be. What I really want is a way to improve collection at the TS, well, just because it's messy. It's a 2HP cyclone on a ductwork system, and like I said, it does a great job on most of my tools, so there's plenty of CFM and velocity. I assume the biggest problem at the TS is the amount of airflow coming in through places other than at the blade, so I thought about duct taping over the vents on the cabinet door, but then I figured those vents are there for a reason and decided against that. I guess there's not much that can be done about the giant holes around the handwheels. So I'm kind of at a loss about what to do. The one thing I know I don't want is one of those overhead monstrosities, mostly because I don't like things in my way, and also because I'm looking for a cheap(er) solution. I bet you guys have a few brilliant tips. Lay 'em on me! Quote
fransikaner Posted August 16, 2012 Report Posted August 16, 2012 Fine Woodworking has a good starter article that basically says do your air flow analysis and stop up all holes, cracks, and cervices that detract from it. http://www.finewoodworking.com/Workshop/WorkshopPDF.aspx?id=32303 I believe you have to be a member to access the article. The most useful info I found was using magnetic sign material or something magnetic to seal around the quarter moon opening for the 45 degree swing gap. I run an Excaliber and am pleased (not blown away) with the added overhead dust collection and protection (until you start making 1" rips.....) The holy grail is how best to capture dust that shoots forward along blade travel and escapes any dust collection efforts short of some flexible, adjustable collector at the front of the TS. Strategies that have worked for me: Foam insulation Opening the TS DC hole to at least 5" Spending some time under the hood to see if the addition of cardboard or thin wood would create better flow surfaces Magnetic sign materials Dynamat and foam to reduce vibration and level out interior surfaces Good luck. your sinuses will thank you later. Quote
Eric. Posted August 16, 2012 Author Report Posted August 16, 2012 Good tips there man! The magnetic sign material is a great idea. So what are your thoughts about covering the vents that allow the motor to breathe? You think there's enough air exchange in there with the DC running that the vents become moot? I'm a little paranoid about suffocating and overheating it. Quote
fransikaner Posted August 16, 2012 Report Posted August 16, 2012 Great question, and one I thought about after I posted. First - if you are NOT running the DC, i would open up some sort of variable venting to ensure you do get that critical airflow. The DC should be pulling 600CFM+, so you need to spend some time on airflow analysis to ensure that air is washing over the motor effectively. A good configuration would see air entering in through the blade guard and the read of the machine above the DC outlet and washing around the motor to the exit. That is where cardboard/ply channels would be of immense value. Quote
rodger. Posted August 16, 2012 Report Posted August 16, 2012 Adding an "over the blade" collector helps a lot with a TS. You can buy one ($$$), or modify your blade guard to fit your shop vac hose. http://www.woodmagaz...dust-collector/ Quote
robjeffking Posted August 19, 2012 Report Posted August 19, 2012 I agree with franklin about the overhead collection. The dust escaping my ts comes from debrs flying over the top of the blade during cuts. Quote
Eric. Posted August 19, 2012 Author Report Posted August 19, 2012 Yeah, I'm sure that's the most effective solution...I just don't want one. Quote
rodger. Posted August 19, 2012 Report Posted August 19, 2012 Yeah, I'm sure that's the most effective solution...I just don't want one. why so? Quote
Eric. Posted August 19, 2012 Author Report Posted August 19, 2012 why so? I don't know, guess I can't really give you a good answer, except I don't like anything around my TS blade. I like to have a clear view and no obstacles near it. I'm one of those counter-intuitive guys who feels safer without all the apparatuses. Less is more kind of thing. Otherwise you're right, that's the obvious solution. Quote
fransikaner Posted August 20, 2012 Report Posted August 20, 2012 The overhead is a significant piece of the overall DC equation, but the downdraft on a properly tuned TS is the moneymaker IMHO. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.