Recommended Posts

Posted

I've been off the forum for a while but still chucking away in the garage shop and reading the articles on Marc site.

I've been using my old Craftsman table saw for about three years now. This saw replaced an even older one. Both saws are missing all safety equipment. I rebuilt this saw and all the parts for the knife and guard where not available at that time. So I went without.

I've been doing my best to be safe, push sticks, zero clearance inserts and feather boards and I haven't had a problem (yet).

Most parts are available now, so the question is go with original knife and guard or the MJ splitter system.

Sears no longer sells the pawls that go with the knife.... so just the knife and the plastic guard.

http://www.searspartsdirect.com/partsdirect/part-model/Craftsman-Parts/Saw-Parts/Model-113299315/0247/0744600/10046763/00006?blt=06&prst=0&shdMod=113299315

or do I go with the MJ splitter http://www.rockler.com/product.cfm?page=10889&site=ROCKLER

I get the impression the original knife on these saws are discarded due to being a pain to use. I also can't get the pawls, not sure if another makers would work...

any suggestions.

Maybe a new saw for Christmas :)

Posted

I have both the orginal splitter and guard for my saw, which I use most of the time. I also have the MJ splitter (yellow version) that I use quite a bit as well. If you have no safety equipment, the MJ splitter is a quick, inexpensive, and easy way to get a spliiter on your saw. You can also make your own splitter (which I have done in the past), but it is not as nice as the MJ in my experience.

If you can afford the shark guard, go for it. The major issue with the SG is that it costs as much as an entry level TS and is avoided by many as they can put that money toward a new saw with better features.

Bottom line - no project is worth your fingers. Get some safety gear ot a new saw ASAP.

Posted

Before I had a riving knive, I liked the splitters I built into my shop-made inserts best. They were quartersawn white oak, sized to the blade, oriented vertically. They lasted YEARS!

After that, I liked my MJ, but I did have a kerf close tight enough to pull a plastic MJ out of it's mounts. The MJ that came loose did it's job well enough to allow me to stop the saw safely, but it did come loose. The newer metal versions probably wouldn't have come out. That piece of reaction wood probably would have gotten stuck on a riving knife. The bottom line in all three cases is that the kerf is held open, the blade isn't pinched, and there's no kickback.

I've used lots of saws in a lots of shops, and I've never understood the attraction of the Shark Guard. The best guards are overarm guards, as they stay on for the most cuts, collect dust, and are easy to move in and out of position. The best splitters are riving knives. They're so good, OSHA doesn't require silly anti-kickback pawls. To me, the Shark Guard is simply a slightly improved stock guard, with many of the drawbacks of stock guards that are included free with many saws still present.

Posted

Ya the shark guard looks nice but it's way more than I paid for the saw and the rebuild. Safety is a concern for me, I don't want my hobby taking me out of work. I actually got rid of a radial arm saw just because it looked and felt like a death trap.... I also make markings on any fence I make for my miter gauge "no fingers here".

I'll probably try the MJ and keep stuffing a little cash into my tool envelope for a new saw. I'd like to pick up a heavier saw so I'll keep looking.

I also want to make a auxiliary fence to mount a feather board for downward pressure for long rip cuts.

(on a side note I'm getting a 14" jet band-saw and a 6" jointer tomorrow :)

Thanks a lot for the feedback, that's one thing I love about this community!

Posted

I came from an old Craftsman TS but finally bought my Grizzly 1023RLWX. I unpacked it and immediately made a zero clearance insert and never installed anything else. I grew up using saws that had no safety equipment so I don't really see the need. Most of the videos you see say that the safety equipment has been removed so you can better see what they're doing. I think the truth is, their saw doesn't have it either and they're just extra careful (as am I) and just don't use it. Most of the time when I've had a serious kickback, I've don't something stupid. I don't mean to sound arrogant....bad things can happen to the most careful of us but I also think you can over engineer anything.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 47 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined