Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Wear and Tear on end grain cutting board finish

Featured Replies

Hi,

New to the forums for me....Hello everyone!

I've recently completed my first end grain cutting board (thanks Marc for the inspiration/plans!). I was extremely pleased with my first attempt- Hard Maple + Black Walnut w/ General Finishes Salad bowl finish. I follow Marc's suggestions to a tee with one exception: On my last coat of finish, I didn't dilute it with mineral spirits. The other 2 were diluted.

Here is the issue: After a single use, the finish on my board is...well...all cut up (see photo). Is this to be expected? I understand that there will be wear and tear, but I was expecting a bit better look after 1 use.

I'm thinking of making these for gifts, but I'm not so sure unless I can get the finish to hold up a bit better.

Any thoughts/comments? Is this normal? What should I do differently the finish?

thanks

post-7628-0-56258200-1350826287_thumb.jp

From the MSDS, that seem to be an urethane based finish. In my humble newbie opinion, you might have built a film on top of that board that is "to thick". If i remember correctly, Marc, in his video, dilutes the 1st couple coats so the finish enters the wood deeply and doesn't stay on the surface of the board as a film.

The way i finish my cutting board is a mix of 2 techniques. I do dilute the 1st few coats. i flood the wood with the diluted finish, and when it is still very wet, i take a 320-400grit sandpaper and sand the finish and the wood until it is a little pasty looking. i wait 5 minutes and wipe of the excess. that seals the pores quite nicely.

after that, i switch to mineral oil and coat the board with it. the sealed pores do no let the oil soak into the wood, so the board remains very shiny, even after multiple uses/wash.

if you you build a solid urethane film on top of your board it will scratch like that in no time. Maybe sand it back to the wood and put some mineral oil on it? something that doesn't cure and harden like that salad bowl finish

gj on the board !

here is mine !

post-7625-0-36286100-1350827400_thumb.jp

I like to use the basic mineral oil and wax mixture. Easy to apply and no mineral spirits needed. Another plus to this is that the future owners will not have problems finding or applying this mixture. Many people prefer this finish to the urethane based finishes because it is natural.

I usually fore-go a film type finish and use a beeswax / mineral oil finish (Claphams salad bowl finish). I'll touch it up probably every other month which takes about 5 min (we use our boards daily) You'll still see some cut marks, but they are pretty subtle..

I use Howards butcher block maintenance mix ... you can get this at Amazon or Rockler

  • Author

Thank you all for the comments/suggestions. I suspect Guillaume Breton is right...I probably built up too much of a finish and its the finish that is showing the scratches. I'll probably take it back down to the wood again and try again.

Some beautiful work displayed here! Guillaume Breton and DJO Furniture Maker...Awesome stuff!

If properly maintained, the more you use the board, the smoother it will feel.

Tip: When I sand, on my last grit, I spritz the whole thing with water.That pulls up the fibers and your last grit will knock them off. If you don't, you'll find that after your first use (when you clean), your board will feel "fuzzy". So, I try to take care of that for my customers. The grain will still stand up, but nowhere near as bad.

I then use mineral oil and as a final coat, a mineral oil and beeswax paste. I apply it like shoe polish, working the paste into the wood. Over the course of time, working the wax in versus wiping only smooths the surface. My boards look and feel better today than the day I made them.

I clean the board on every grit of sanding .... 100 grit sanded with a rotex, plus clean with a wet towel ... 120 .. 150 ... 180 ... 220 ... by the end is fantastic. The last grit I just vaccum it off because I don't want to raise the grain anymore.

I wonder if the salad dressing finish is too hard. Any comments?

If properly maintained, the more you use the board, the smoother it will feel.

Tip: When I sand, on my last grit, I spritz the whole thing with water.That pulls up the fibers and your last grit will knock them off. If you don't, you'll find that after your first use (when you clean), your board will feel "fuzzy". So, I try to take care of that for my customers. The grain will still stand up, but nowhere near as bad.

I then use mineral oil and as a final coat, a mineral oil and beeswax paste. I apply it like shoe polish, working the paste into the wood. Over the course of time, working the wax in versus wiping only smooths the surface. My boards look and feel better today than the day I made them.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.